1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm=2k Im=(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V.

1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm=2k Im=(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The step up chopper has R=20 ohm and out put voltage is 120V. The source voltage is 40V DC . The load inductance is 0.2mH. If the chopper frequency is 4KHZ find1- the duty cycle2- the average value of source current3- TON4- Imax5- Imin6-The average value of diode current
In the figure given we have u(t)=10. cosot [V]. We assume the diodes and the A-meter (A) to be ideal. A u(t) a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. R1 1 R2 102
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
The given figure shows a step-down dc chopper. A freewheeling diode is placed across the load. The TON would be TOFF load current varies between the limits of 10 A. The time ratio 100V KH 40 mH vvvvv io 5Q
Q: - Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. 4:1 D, 120 V rms c) If sin wave with 100µf connected in parallel with the resistor, calculate the ripple сарacitor is 60 HZ 1.0 kN D2 factor lllee lelll
Q1: ideal diodes are used in the circuit shown in figure. Sketch the output voltage 1Kohm D3 V=10Sinwt D2 Vo + El-7V- E2-5v+
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal resistance of the ammeter is 5 K2, the voltage across the internal resistance is 0.5 v and the resistance of the diodes in the forward direction is 1 K2, find the multiplier resistance and sensitivity. Assume half wave rectification and a shunt resistance across the meter. The value of the shunt resistance across the ammeter is 2.5 KQ. Q2) Re-design the question above for full wave rectifier (without Rsh)
A three-phase rectifier is supplied by a 173.2-V rms line-to-line 60-Hz source. The RL load is a 100 resistor in series with a 15-mH inductor. Determine THD taking Is1 = 1.35
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
AN Sesli oku 1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm32k İm-(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances) ult) R2 本 R3 20k 18k R4 k: k2 10k
A circuit contains a diode in series with a 500 Ohm resistor. The diode is oriented to all current towards the positive side of the power source. Plot the theoretical I-V curve.