1. Use a VCO with frequency sensitivity 2 KHz/mV and quiescent frequency 198 KHz togenerate an FM signal s(t) = 10 cos(400лt + (t)), where the unit of time ismilliseconds, and the phase (p(t) is as sketched in the following figure. Derive andsketch the input to the VCO.(t)6л3-3124567800t (ms)

1. Use a VCO with frequency sensitivity 2 KHz/mV and quiescent frequency 198 KHz to generate an FM signal s(t) = 10 cos(400πt + p(t)), where the unit of time is milliseconds, and the phase (t) is as sketched in the following figure. Derive and sketch the input to the VCO. op(t) 6л 3 3π 1 t (ms) 2 4 5 6 7 8

1. Use a VCO with frequency sensitivity 2 KHz/mV and quiescent frequency 198 KHz to generate an FM signal s(t) = 10 cos(400πt + p(t)), where the unit of time is milliseconds, and the phase (t) is as sketched in the following figure. Derive and sketch the input to the VCO. op(t) 6л 3 3π 1 t (ms) 2 4 5 6 7 8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Give a real life example of a filter used in digital signal processing and explain why it is necessary.
Problem1: the figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: 1. What is the value of the duty cycle in A? 2.What is the quantization noise in a modulator that uses a 4-bits register for the analog to digital conversion of the given sinusoidal signal?
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: (i) The peak amplitudes of the audio, carrier sideband voltages and modulation index. (ii) Using the above results, write the complete AM mathematical representation to express the waveform, showing its carrier, lower sideband and upper sideband parameters. (iii) The power of the carrier signal, total sidebands power and the bandwidth of the modulated signal. Then sketch and label the power spectrum of the modulated ( i v ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC
A digital communication link carries binary-coded words representing samples of an input signal, xa(t)=3cos⁡(600πt)+2cos⁡(1800πt)The link is operated at 1,000 samples/s. (a) What is the folding frequency? (b) What is the Nyquist rate for the signal xa(t)? (c) What are the frequencies in the resulting discrete-time signal x(n)? (d) Will there be any aliasing here? (e) Which frequency will alias to what frequency
A subcarrier given in Eq. 4.1 is amplitude modulated by an information signal given in Eq. 4.2. The resulting AM signal is then used to amplitude modulate the signal given in Eq. 4.3 to generate a signal that is finally transmitted. Derive a mathematical expression for this final signal that is transmitted. How, in practice, can this system be made with minimum harmonic distortion? Equations for Question 04
kindly explain this part ,, how sinc100t is represemted in frequency domain
You have an FSK transmitter using a mark frequency of 500 kHz, a space frequency of 380 kHz, and sending 10 kbps. A) How much bandwidth do you need for your transmission? B) if you are to design the system with continuous phase shift keying in mind, what would be the value of the space frequency if the mark frequency remains the same?
A 2000-Hz audio signal having an amplitude of 15 V amplitude modulates a 100- KHz carrier which has a peak value of 25 V when not modulated. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
In the traditional amplitude modulated signal time domain; The message signal m (t) is defined as the amplitude of the carrier signal Ac and the frequency of the carrier signal in the following form: The modulated signal we obtained as a result of the traditional amplitude modulation experiment that we made with a single-tone (that is, a single frequency component) sinusoidal message signal in our laboratory is as shown in the figure. . According to this;a) Draw the modulated sign in the time domain. Find the modulation index. b) Interpret by determining the ratio of the power in the sidebands to the total power.
1. We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =2,000Hz. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.
An audio signal given by 15 sin(4000ntt) + 20 sin(8000mt) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60 sin(100,000nt) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why?
Determine the time domain signal ?(?) using its magnitude and phasespectrum given in the figure below.