2. A P&ID of a phosphate pebble dryer is shown in the figure below. A feeder (table feeder) moves the pebbles into the dryer under automatic feedback control to maintain the outlet pebble moisture concentration (wt% moisture) at 3 wt%. If the pebbles leave the dryer too dry, they may break down into a fine powder, which will be unusable. If the moisture level of the pebbles leaving the dryer is too high, then they may agglomerate and form unusable chunks of material in the storage silo and could plug the flow from the silo. The speed of the feeder table is directly proportional to the output of the moisture controller (M(t); signal has the range of 0- 100 %CO). The moisture transmitter has an operational range of 1 wt % moisture to 5 wt % moisture, and sends a 0 – 100 %TO signal to the moisture controller. MC I. D. fan Stack Table feeder, MT Bed Fuel Combustion furnace Conveyor Windbox Combustion air a) (28.6%) What is the action of the moisture controller? Please show your work.

2. A P&ID of a phosphate pebble dryer is shown in the figure below. A feeder (table feeder) moves the pebbles into the dryer under automatic feedback control to maintain the outlet pebble moisture concentration (wt% moisture) at 3 wt%. If the pebbles leave the dryer too dry, they may break down into a fine powder, which will be unusable. If the moisture level of the pebbles leaving the dryer is too high, then they may agglomerate and form unusable chunks of material in the storage silo and could plug the flow from the silo. The speed of the feeder table is directly proportional to the output of the moisture controller (M(t); signal has the range of 0- 100 %CO). The moisture transmitter has an operational range of 1 wt % moisture to 5 wt % moisture, and sends a 0 – 100 %TO signal to the moisture controller. MC I. D. fan Stack Table feeder, MT Bed Fuel Combustion furnace Conveyor Windbox Combustion air a) (28.6%) What is the action of the moisture controller? Please show your work.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter22: Basics Of Electronics And Computer Systems

Section: Chapter Questions

Problem 4RQ: Means that data concerning the effects of the computers commands are fed back to the computer as an...

See similar textbooks

Similar questions

The level of liquid in a reboiler on a distillation column is controlled by using feedback control to throttle a valve on the liquid product (see below P&ID). However, the pressure of vapour above the liquid in the reboiler also affects the flow rate of liquid product, as an increase in pressure above the liquid will push the liquid through the product line faster. a) Draw a cascade arrangement where the vapour pressure is measured as the secondary variable. b) Draw a cascade arrangement where the actual flowrate in the liquid product stream is measured as the secondary variable. Feed LTC vapour liquid Liquid product
Using signavio or any PBM tools and must Use pool and lane and object. Model the following business process at a supplier. After a supplier notifies a retailer of the approval of a purchase order, the supplier can receive an order confirmation, an order change, or an order cancelation from the retailer. It may happen that no response is received at all. If no response is received after 48 h, or if an order cancelation is received, the supplier will cancel the order. If an order confirmation is received within 48 h, the supplier will process the order normally. If an order change is received within 48 h, the supplier will update the order and ask again the retailer for confirmation. The retailer is allowed to change an order at most three times. Afterwards, the supplier will automatically cancel the order.
SUBJECT: Feedback & Control Systems
An oil/gas separator is a pressure vessel used for separating a well stream into gaseous and liquid components. They are installed either in an onshore processing station or on an offshore platform. Based on the vessel configurations, the oil/gas separators can be divided into horizontal, vertical, or spherical separators. In a three phase separator, the secondary separation section is designed to facilitate the separation of the liquid constituents into light and heavy phases according to their_________________. a. gravity b. viscosity c. specific gravity d. density
Using "Subjective Digital Design", please develop the Boolean equation for the problem statement given: This CNC machine controller allow operation (represented by O) of the machine if there is a part in the vice (determined by a sensor P) and the spindle is fully retracted (determined by another sensor R) or a manual override (M) button is pressed by the operator.
Speed reduction, either through gearing or belt-pulley constructs, is an important element in motion system design. Similarly, converting rotary motion to linear motion is an important consideration. Considering a printer system driven by a stepper motor with 200 steps per revolution, construct a table that shows the relationships for: a. Position resolution of the print head vs. angular position of the motor. This translates to addressable print dots per mm vs. step angle. b. Print head speed (mm/S) vs. motor speed (Steps/S with rpm also noted) C. Frictional load at the print head (mN) vs. reflected torque at the motor (mNM) Mass of the print head vs. reflected inertia to the motor d. Use GR for Speed Reduction, r (mm) for the radius of the drive pulley, and m (grams) for print-head mass.. Belt Actuator Load Drive Pulley Secondary Pulley Linear Guide Belt Primary Pulley Motor
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
Means that data concerning the effects of the computers commands are fed back to the computer as an input signal.
part a is not 5.2 got it wrong Dear expert don't Use chat gpt
Suppose a process has been monitored daily for the last ten days and the number of machine failures each day was noted. The results follow: Day Number: 1 2 3 4 5 6 7 8 9 10 Number of Failures: 8 9 6 10 12 4 9 11 9 12 Compute control limits for a c-chart that monitors the average number of machine failures per day. Is the process in a state of control?
= Consider a four aisle AS/RS in which an S/R machine is used for each aisle. The length of the storage aisle 85 m and its height = 14 m. Suppose horizontal and vertical speeds of the S/R machine are 61 m/min and 23 m/min, respectively. The S/R machine requires 20 s to accomplish a P&D operation. The aisles in the AS/RS will be organized to follow a class-based dedicated storage strategy. There will be two classes, according to activity level. The more active stock is stored in the half of the rack system that is located closest to the input/output station, and the less active stock is stored in the other half of the rack system farther away from the input/output station. Within each half of the rack system, random storage is used. The more active stock accounts for 80% of the transactions, and the less active stock accounts for the remaining 20%. Assume that system utilization = 90%, and the number of single-command cycles = the number of dual-command cycles. Determine the throughput…
The main reason to do Design for Manufacturing (DFM) is? O a. To predict costs O b. To improve the design of the products Oc To predict time O d. To estimate cost evaluation for further system analysis: