2. A water tank is fitted with a drain and outlet pipe as shown in the figure. The system has 82 feet of cast iron pipe of 1-½" diameter. Determine the flow rate through the pipe. All fittings are threaded and regular. (Q=0.077 m³/s) f = 0.034 Kentrance = 0.5 Kreturn bend = 1.5 Kelbow = 1.4 Kglobe valve = 10 Kexit = 1.0 15 ft. Fully open globe valve Kentrance 8 ft. I Kelbow Kesu Pond return bend Kglobe valve

2. A water tank is fitted with a drain and outlet pipe as shown in the figure. The system has 82 feet of cast iron pipe of 1-½" diameter. Determine the flow rate through the pipe. All fittings are threaded and regular. (Q=0.077 m³/s) f = 0.034 Kentrance = 0.5 Kreturn bend = 1.5 Kelbow = 1.4 Kglobe valve = 10 Kexit = 1.0 15 ft. Fully open globe valve Kentrance 8 ft. I Kelbow Kesu Pond return bend Kglobe valve

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EGL and HGL. h2 Water T = 10°C (50°F) Globe valve
Water flows through a 300mm diameter pipe at a velocity Of 3.00 m/s. Determine the weight flow rate in N/s. Do not write the unit. You will only jnput the numerical answer in the space provided. Unit of the Correct Answer: N/s O 9810.000 O 2,080.284 O 8829.000 1202.284
2. A water tank is fitted with a drain and outlet pipe as shown in the figure. The system has 82 feet of cast iron pipe of 1-½" diameter. Determine the flow rate through the pipe. All fittings are threaded and regular. f = 0.034 Kentrance = 0,5 Kreturn bend = 1.5 Ketbow = 1.4 Kytobe vatve = 10 Kexit = 1.0 15 ft. Fully open globe valve Kentrance Kethow Kesn Pond Ketum hend
(Flow through Single Pipes). Determine the flow in each pipe and the pressure at the junction node, D. Assume elevation at Node, D to be 328 feet and friction factor, f, of 0.02 for all pipes. [NOTE: This is a three-part problem]. A B Elevation (ft) Length (ft) 19,680 Diameter (ft) Reservoir Pipe Part A) A 656 AD 3.28 В 590 BD 13,120 2.5 558 CD 29,520 2.5 19,680 13,120 Part B) A 656 AD 3.28 В 574 BD 3.28 CD 29,520 19,680 19,680 492 2.5 Part C) A 656 AD 3.28 В 590 BD 3.28 492 CD 19,680 3.28
Question 7 A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 120 (Hazen-Williams) Pipe 2 n = 0.020 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
Question 6 In the schematic below, water flows through the pipe and enters a sudden contraction nozzle. To hold the nozzle in place, calculate the axial component of an anchoring force (FA) that would be necessary. Provide a sketch of your control volume. p = 1.940 slugs/fts, 1 ft = 12 inches, 1 lb-s? = 1 slug-ft Section (1) Uniform flow P-75[psi] V,-25[ft/s] Section (2) Uniform flow P2=0 [psi] V=100[ft/s] D;=3 [in] Flow in circular pipe Flow in circular pipe Sudden contraction nozzle
For the pipe system, determine Q. 150 R = 2 80 II R = 1 R = 3 R =1 30 R = 2 Q Answer:
This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. What will be the gage pressure reading at A? correction: 3.75 mm should be 375 mm en Me Do not write the unit. You will only input the numerikal answer in the space provided. Unit of the Correct Answer. kPa Decimal Places required in the firal answer 3
Question 7 2 pts A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 100 (Hazen-Williams) Pipe 2 n = 0.015 (Chezy-Manning) Pipe 3 f = 0.020 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.
1%VY lI. lu. Home work 1.pdf -> Home work 1 Three pipes of 400 mm, 200 mm and 300 mm diameters have lengths of 400 m, 200 m, and 300 m respectively. They are connected in series to make a compound pipe. The ends of this compound pipe are connected with two tanks whose difference of water levels is 16 m. If co-efficient of friction for these pipes is same and equal to 0.005, determine the discharge through the compound pipe neglecting first the minor losses and then including them. II
Find the cost of the pumping water Cost = r*P. where r= 0.3353 is the interest rate and Pis the absolute pressure )( kpa) in the pipe. Water Air 60 cm 50 cm 40 cm 50 cm S=0.8 S-0.5 45 deg