A 1.7-m-long thin vertical plate is subjected to uniform heat flux on one side, while the other side is exposed to cool air at 5°C. The plate surface has an emissivity of 0.73, and its midpoint temperature is 55°C. Determine the heat flux subjected on the plate surface.

A 1.7-m-long thin vertical plate is subjected to uniform heat flux on one side, while the other side is exposed to cool air at 5°C. The plate surface has an emissivity of 0.73, and its midpoint temperature is 55°C. Determine the heat flux subjected on the plate surface.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A can of engine oil with a length of 150 mm and a diameter of 100 mm is placed vertically in the trunk of a car. In a hot summer day, the temperature in the trunk is 43°C. If the surface temperature of the can is 17°C, determine heat transfer rate from the can surface. Neglect the heat transfer from the ends of the can.
An 8-m-internal-diameter spherical tank made of 1.5-cm-thick stainless steelAISI 302 is used to store iced water at 0°C. The tank is located in a roomwith temperature 25°C. The outer surface of the tank is black (emissivity, ε= 1), the heat transfer between the outer surface of the tank and thesurroundings is by natural convection and radiation. The convection heattransfer coefficients at the inner and the outer surfaces of the tank are 80W/m2K and 10W/m2K, respectively; and the outer surface temperature of thetank is 5°C. Draw the equivalent thermal circuit of the system. Determine the total heat transfer rate to the iced water in the tank and the total amount of ice at 0°C that melts after 24 hours.
what is the convection heat transfer coefficient for ambient air at 43°C
A 6-m-long section of an 8-cm-diameter horizontal hot-water pipe shown in Fig. 9-16 passes through a large room whose temperature is 20°C. If the outer surface temperature of the pipe is 70°C, determine the rate of heat loss from the pipe by natural convection.
The boiling temperature of nitrogen at atmospheric pressure at sea level (1 atm) is -196°C. Therefore, nitrogen is commonly used in low temperature scientific studies since the temperature of liquid nitrogen in a tank open to the atmosphere will remain constant at -196°C until the liquid nitrogen in the tank is depleted. Any heat transfer to the tank will result in the evaporation of some liquid nitrogen, which has a heat of vaporization of 198 kJ/kg and a density of 810 kg/m3 at 1 atm. Consider a 3-m-diameter spherical tank initially filled with liquid nitrogen at 1 atm and 196°C. The tank is exposed to 22°C ambient air with a heat transfer coefficient of 22 W/m2 · °C. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the nitrogen inside. Disregarding any radiation heat exchange, determine the rate of evaporation of the liquid nitrogen in the tank as a result of the heat transfer from the ambient air in kg/sec. Answer in…
Consider a hot automotive engine, which can be approximated as a 0.5-m-high, 0.40-m-wide, and 0.8-m-long rectangular block. The bottom surface of the block is at a temperature of 100°C and has an emissivity of 0.95. The ambient air is at 20°C, and the road surface is at 25°C. Determine the rate of heat transfer from the bottom surface of the engine block by convection and radiation as the car travels at a velocity of 80 km/h. Assume the flow to be turbulent over the entire surface because of the constant agitation of the engine block.
Consider a 0.6-m x 0.6-m thin square plate in a room at 30°C. One side of the plate is maintained at a temperature of 90°C, while the other side is in- sulated, as shown in Fig. 9-18. Determine the rate of heat transfer from the plate by natural convection if the plate is (a) vertical, (b) hor izontal with hot surface facing up, and (c) horizontal with hot surface facing down.
A 0.5-m-long thin vertical plate is subjected to a uniform heat flux of 1200 W/m2 on one side, while the other side is exposed to hydrogen gas at 5°C. Assuming that the properties of the hydrogen gas can be evaluated at 50°C, determine the plate midpoint temperature TL / 2. Is 50°C an appropriate film temperature for evaluation of the properties of the hydrogen gas?
9-24 A 0.5-m-long thin vertical copper plate is subjected to a uniform heat flux of 1000 W/m² on one side, while the other side is exposed to air at 5°C. Determine the plate midpoint temperature onosed to air at 5°C. Determine the plate midpoint temperature for (a) a highly polished surface and (b) a black oxidized surface. Hint: The plate midpoint temperature (T,2) has to be found itera- tively. Begin the calculations by using a film temperature of 30°C. Copper plate (highly polishe Copper plate (black oxidized) T surr Air Air 5°C 5°C TL2 (a) (b) We must consider radiation. Use ɛ = 0.02 for polished copper and ɛ = 0.73 for black oxide finish. Ans: a. 147.2°C b. 88.5°C. Show all steps and at least 1 iteration. 1000 W/m² 1000 W/m2
A 0.2-m-long and 25-mm-thick vertical plate (k= 15 W/m∙K) separates the hot water from the cold water. The plate surface exposed to the hot water has a temperature of 100°C, and the temperature of the cold water is 7°C. Determine the temperature of the plate surface exposed to the cold water (Ts,c). Hint: The Ts,c has to be found iteratively. Start the iteration process with an initial guess of 53.5°C for the Ts,c .
A thin 100 cm long and 10 cm wide horizontal plate is maintained at a uniform temperature of 150°C in a large tank full of water at 75°C.Estimate the rate of heat to be supplied to the plate to maintain constant plate temperature as heat is dissipated from either side of plate. Don't Chat Gpt and AI .
The water main in the cities must be placed at sufficientdepth below the earth’s surface to avoid freezing duringextended periods of subfreezing temperatures. Determine theminimum depth at which the water main must be placed ata location where the soil is initially at 15°C and the earth’ssurface temperature under the worst conditions is expected toremain at -10°C for a period of 75 days. Take the propertiesof soil at that location to be k = 0.7 W/m·K and a = 1.4 *1025 m2/s.