A crucible and its cover weigh 65.82 grams. You add a hydrate of a salt and it now weighs 83.77 g heat the crucible, cover slightly ajar, until the contents are completely dry and it now weighs 81.06 9, 10. Calculate the experimental percent water in the sample in this hydrate. 11,12.Calculate the theoretical percent of water for the compound FeSO, 7H20

A crucible and its cover weigh 65.82 grams. You add a hydrate of a salt and it now weighs 83.77 g heat the crucible, cover slightly ajar, until the contents are completely dry and it now weighs 81.06 9, 10. Calculate the experimental percent water in the sample in this hydrate. 11,12.Calculate the theoretical percent of water for the compound FeSO, 7H20

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter11: Intermolecular Forces And Liquids

Section11.6: Properties Of Liquids

Problem 1.2ACP

See similar textbooks

Similar questions

11. 50.0 g of silver nitrite is mixed with 50.0 g of hydrochloric acid in a water based solution. A white precipitate forms. The solution is filtered and the white precipitate collected and dried. The dried precipitate is measured to have a mass of 36.1 g. What is the percent yield?
3.A core sample is saturated with an oil (po = 35°API), gas and water. The initial weight of the sample is 224.14 g. After the gas is displaced by water (pw = 1 g/cm'), the weight is increased to 225.90 g. The sample is the placed in a Soxhlet distillation apparatus, and 4.4 cm' water is extracted. After drying the core sample, the weight is now 209.75 g. The sample bulk volume, 95 cm3 is measured in a mercury pycnometer. Find the porosity, water saturation, oil saturation, gas saturation and lithology of the core sample.
A sample may contain any combination of sodium hydroxide, sodium carbonate and sodium bicarbonate with inert matter. A 3.00g sample requires 57.57ml of 0.5N hydrochloric acid to reach phenolphthalein endpoint and a total of 105.4ml of acid was used until the methyl orange endpoint was reached. What is the percentage inerts in the mixture? What is the percentage sodium bicarbonate in the mixture? What is the percentage sodium hydroxide in the mixture? What is the percentage sodium carbonate in the mixture?
A pheromone is a type of volatile compound produced by a variety of insect species for chemical communication. These molecules can be used to signal alarm, to attract a mate, or to indicate the presence of food. The presence of 1.00 x 10-8 g of a pheromone can be sensed by another insect within a radius of 0.500 miles. Calculate the density of this pheromone. (1609 m = 1 mile) %3D Calculate the density (g/L) of the pheromone in this cylindrical air space.
(10) You have 4 powdered samples, A, B, C, & D. One sample contains fullerenes, C16 to C70. Another is nano diamond. Another one is a mixture of C60 and carbon nanotubes. The 4th is a mixture of graphite & graphene. Indicate the analytical methods you would use to identify and distinguish the samples from each other.
A 25mL volumetric pipet is used to deliver a sample of the stock solution marked “0.6000M X2SO4” into a 100mL volumetric flask. Distilled water is added to the flask until it is about 3/4thfull, the solution is mixed well, then more water is added to fill it up to the calibration mark, then it is mixed again. Calculate the concentration of X+ion in the dilute solution made above.
An experiment was performed to look at how density changes when t he ratio of water and ethanol was changed. The following data was obtained: % Mass Ethano1.00 2.50 3.50 4.00 6.00 7.50 9.50 Density, g/mL0.9963 0.9936 0.9918 0.9910 0.9878 0.9855 0.9826 Use Excel or a similar spreadsheet program to plot these six data points and answer the following questions . a.What is the independent variable? b.What is the dependent variable? c.What is the equation of the best-‐fit line? d.What is the value of the coefficient of determination? e. According to the best-‐fit line, what should the density of pure water be (i.e. what is the density when % mass ethanol = 0.00)?
Weigh out accurately 9.99 g of copper(II) sulfate pentahydrate (CuSO4·5H2O) by taring using a clean and dry empty 250-ml beaker. 2. Add tap water to the beaker to reach the 50-mL mark on the side of the beaker. 3. Dissolve all the crystals of CuSO4·5H2O in the water using a clean glass rod for stirring. 4. Then using a glass funnel transfer all the blue solution to a 100-mL volumetric flask. Rinse the beaker with about 10 mL of water and transfer the solution to the volumetric flask. Repeat the rinsing of the beaker with another 10 mL of water and transfer the solution to the volumetric flask. This is called quantitative transfer of the solution. 5. Then add enough water to reach the calibration mark of the volumetric flask. (You will need to use a dropper to add the last few drops of water to ensure the meniscus is on the calibration mark). Close the volumetric flask with a stopper and mix the solution well (so that it is homogeneous). 6. You have now prepared a standard solution (or…
a hydrated CuSO4 salt was heated and thus dehydrated. Determine the % H2O by weight in the hydrated CuSO4 salt. SHOW WORK TO RECEIVE FULL CREDIT mass of empty dish 43.571 gmass of dish + hydrated salt 44.326 gmass of dish + dehydrated salt 44.054 g 4. Using the data found in question number 3, determine the empirical formula for the hydrated CuSO4salt. What is the chemical name of this dehydrated salt? 5. Suppose that after your second heating, you were impatient and did not wait until your porcelain evaporating dish to cool. Instead, you weighed it while it was still hot. How would this specifically affect the calculated percentage of water in the compound?
A core sample is saturated with an oil (?o = 35oAPI), gas and water. The initial weight of the sample is 224.14 g. After the gas is displaced by water (?w = 1 g/cm3 ), the weight is increased to 225.90 g. The sample is the placed in a Soxhlet distillation apparatus, and 4.4 cm3 water is extracted. After drying the core sample, the weight is now 209.75 g. The sample bulk volume, 95 cm3 is measured in a mercury pycnometer. Find the porosity, water saturation, oil saturation, gas saturation and lithology of the core sample.
A chemist mixes 49. g of chloroform with 53. g of acetyl bromide and 29. g of acetone. Calculate the percent by mass of each component of this solution. Be sure each of your answer entries has the correct number of significant digits. component mass percent x10 chloroform |% ? acetyl bromide acetone
A homogeneous mixture consists of 5% methanol, 70% isopropanol, and 25% water. Label these components as solvents or solutes. methanol: [ Select ] isopropanol: [ Select ] water: [ Select ]