Please solve correctly much important to me Question 2A hollow circular section shaft 2.5 m long is firmly supported at each end and has an insidediameter of 50 mm. The shaft is subjected to a torque of 14 kN m applied at a point 1.5 m fromone end. If the shear stress in the shaft is limited to 150 MPa and the angle of twist to 2,calculate the maximum allowable outside diameter. The shear modulus G = 80 000 N/mm2.

Answered: Image /qna-images/answer/37a5d526-fc74-4ccc-8666-19eb7b87d89d.jpg

Answered: A hollow circular section shaft 2.5 m…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 72 mm and G = 30.49 GPa. For the steel segment BC, the diameter is 48 mm and G = 83.57 GPa. Given that a = 2.09 m and b = 1.48 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.49 MPa in the bronze and 85.69 MPa in the steel. Round off the final answer to two decimal places.
The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1168.7 Nm, U = 4515 Nm, x = 3.01 m, y = 2.36 m, z = 1.35 m, d = 90 mm, and e = 83 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places. U T Aluminum Steel Bronze
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
A solid shaft 100 mm in diameter is subjected to an axial compressive load of 600 kN simultaneously with a torque that twists the shaft thru an angle of 1.5 degrees in the length of 8 meters. If G=80Gpa, compute the maximum normal stress in the shaft. This is a COMBINED STRESS problem. Please include drawings of the circle.
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. A 400 N-m 850 N-m L=1.4 m 30 mm diameter B L=2.4 m 50 mm diameter L-1.9 m 30 mm diameter
The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds of its outer diameter D. If the inner diameter is 8 inches, find the angle of twist of the shaft. Use G = 12 x 10^6 psi for steel.
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
Calculate the torque T: i. if the shear stress of the brass sleeve in section AB is limited to τb = 70 MPa.ii. if the shear stress of the steel shaft in section BC is limited to τs = 110 MPa.
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm. If the shear stress in the shaft is not exceed 120 MPa and the angle of twist is not exceed 5; find the largest allowable of P. For steel; use G = 80 GPa.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS