A Compound Steel (G=80GPA) Shaft consists of a solid 90mm diameter (segment1) and a solid 70mm diameter (segment2). The allowable shear stress of the steel is 96MPA, and the maximum rotation angle at the free end of the compound shaft must be limited to c <4°. Determine the magnitude of the largest torque Tc that may apply at C. (1) Tc (2) B. IC 1.2 m 1.8 m

A Compound Steel (G=80GPA) Shaft consists of a solid 90mm diameter (segment1) and a solid 70mm diameter (segment2). The allowable shear stress of the steel is 96MPA, and the maximum rotation angle at the free end of the compound shaft must be limited to c <4°. Determine the magnitude of the largest torque Tc that may apply at C. (1) Tc (2) B. IC 1.2 m 1.8 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube is r1 = 45 mm and the measured angle of twist betweenthe ends is 0.5°, what is the shear strain γ1 (in radians) at the inners surface? b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to bekept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius(r2)max?
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa
1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the shaft is to be limited to 3°. (a) Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel. 2. The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1
Q2:The composite torsion member as shown in Fig. If the allowable stresses for steel and aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft is not to twist more than 1.45°, determine the maximum torque T that can be applied to the member. Gs = 84 Gpa, Ga 28 Gpa. Aluminium Steel 75 .mm 100 mm 1m
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
A high strength drill rod used for boring a hole in the earth has a diameter of 50 mm. The allowable shear stress in the steel is 120 MPa and the shear modulus is G=80 GPa 1. Determine the required length of the rod so that one end of the rod can be twisted 4° with respect to the other end without exceeding the allowable stress. 2. Determine the torsional stiffness in N.m.3. Determine the allowable shear strain of the rod.
The steel hollow shaft is rigidly attached to a solid bronze shaft by a bolt coupling. A maximum torque T can be applied to the ends of the shaft without failure. Use G = 83 GPa for steel and G = 35 GPa for bronze. %3! 100 mm 70 mm 70 mm 1.5 m 2 m Determine the maximum torque Tin kN-m without exceeding a shear stress of 70 MPa in steel and 50 MPa for bronze. 1. A) 10.44 Determine the maximum torque Tin kN-m without exceeding an angle of twist of 2.5° in the 3.5-m length. A) 1.20 B) 9.82 C) 8.56 D) 7.35 2. B) 13.51 C) 2.40 D) 12.68 3. Determine the number of 16 mm bolts required to attach the two shafts if the allowable shear stress in each bolt is 30 MPa and the diameter of bolt circle is 150 mm. A) 4 B) 5 C) 6 D) 7 1A
1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b Ay r r=2acose Figure 1: Circular shaft with a keyway. The keyway is represented by the boundary equation r = b and the shaft is represented by the boundary equation r = 2a cos 0. Show that using a Prandtl stress function of the form ²) (₁ (1-2a cos) X v = K (b² − ²) (1 – : will solve the problem of torsion on this shaft and find the constant K (assume an applied torque T). Compute the shear stress components Txz and Tyz. (Hint: start by converting the stress function to Cartesian coordinates).
4. The allowable shear stress in two steel (G = 83 GPa) shafts below is 90 MPa. The design requires that the end D of the shaft CD doesn't rotate more than 4°, and both shafts shall have the same diameter. Determine the required diameter of the shafts. 40 mm T = 1000 N - m D 100 mm 400 mm 600 mm
1. The shaft assembly shown below is fixed at its ends A and D. It consists of an aluminum (G = 30 GPa) segment AB rigidly connected to a steel (G= 75 GPa) segment BCD. Both segments have a 80-mm diameter. If the shaft is subjected to a torque 7 of 9 kN-m applied at C, determine The reactions at A and D; a) b) The angle of twist at point B; The maximum shear stress in the shaft. 300 mm -Aluminum 600 mm Steel C 300 mm
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips