A hollow steel shaft with an outside diameter of 76 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 2035 N-m. The shear modulus of the steel is G = 80 GPa. Determine the maximum shear stress in the shaft. a 75.2 MPa b 54.7 MPa c 63.1 MPa d 58.1 MPa e 69.2 MPa

A hollow steel shaft with an outside diameter of 76 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 2035 N-m. The shear modulus of the steel is G = 80 GPa. Determine the maximum shear stress in the shaft. a 75.2 MPa b 54.7 MPa c 63.1 MPa d 58.1 MPa e 69.2 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Related questions

Q: You have been asked by your engineering company to design a complete gear and shaft system shaft…

A: Given:- TA=15 kN-m(clockwise direction),TB=30 kN-m(clockwise direction),TC=75 kN-m(anti-clockwise…

Q: nd 45 KW at the final stage? 12.45 KW 13.57 KW 14.23 KW 15.14 KW

A: Actual power capacity.

Q: Question 2 In designing prosthetic sockets, the latter will need to be experimentally tested for…

A: Given: The strain along gauge a, εa = 2500x10-6 The strain along gauge b, εb = 1500x10-6 The strain…

Q: An incompressible frictionless flow field is given by V = (Ax + By)i + (Bx – Ay)j where A = 1 si and…

A: The term "velocity field" refers to the dispersion of velocity in a flow zone. It is written as…

Q: nt of inertia Ix (in

Q: 3. For an ideal diesel cycle, the pressure at the beginning and at the end of compression are 98 kPa…

Q: 1. An engine operating on the air diesel cycle with k=1.3 has thermal efficiency of 63% and a…

Q: An object is made to travel along a path y = x and an observer sees that it is travelling…

Q: If the travel ratio of a tractor was found to be 0.90. What is the % slip (wheel slippage)?

A: Given Travel ratio, T = 0.9 Find % Slip, S

Q: A rocket is launched vertically at time t = 0. The elevation of the rocket is given by y = -0.14t* +…

Q: 4- For this truss e=60°, a) Determine the type of supports b) Reaction forces at each support c)…

A: Dear student, According to the expert guidelines, I am allowed to answer only…

Q: 1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes…

A: h1 is the specific enthalpy of saturated liquid water at the exit of condenser corresponding to…

Q: Two compartments in a cylinder with uniform cross section and total length 102 cm are separated by a…

A: Given that, Temperature of the walls, T1=2000 K,T2=4000 K,Total length=102 cm,

Q: 1. Write the differential equation of the vehicle shown in Fig. 1 by summing forces in x-direction…

Q: Consider the following air-conditioning system design which involves a refrigeration process…

Q: Water flow rate is 8.7 gpm (gallons per minute) What is the static head? What is the overall…

A: Static pressure head is the pressure resulting from a column of liquid acting under gravity, and…

Q: 113 Figure 11.15 shows a portion of a hydraulic circuit. 15e pressure at point B must be 200 psig…

A: Given DataQ=60gal/minr=2in=0.16667ftA=π4×0.166672=0.023ft2

Q: If the car passes point A with a speed of 15 m/s and begins to increase its speed at a constant rate…

Q: Find the minimum number of bolts required to hold the two

A: To find Minimum number of bolts required to hold the two members together

Q: A wind tunnel has an inlet section with a velocity of 360 ft/s at standa atmospheric conditions. The…

A: Ans: 403 ft/sec

Q: The diameter and the length of the furnace are 1.0 meters. Its lateral surface (surface 3 lack and…

A: View factor for parallel disk: Fij=12[S-S2-4rjri212]S=1+1+Rj2Ri2Rj=rjL , Ri=riLR2=r2L ,…

Q: (1.3) Suppose a process increases Gibbs free energy of a system coupled to both a heat bath and…

A: Given : ∆G>0 To find : Explain

Q: Find initial length of rod Change in length-0.02 mm Strain-0.0002

Q: What are the sources of error and how can one minimize the error?

A: An error is defined as the difference between two measurements. The measurement error is a…

Q: The compression ratio of an Otto cycle is 5. If the initial pressure is 100 kpa, determine the final…

Q: As a thermo-fluid engineer working for an energy startup located at Greentown Labs, you are tasked…

A: Given Inlet temperature of hot gas, Ti = 52oC Inlet temperature of cold water, T1 = 4oC…

Q: Problem 2. A steel tube of outer radius 5.8 cm is used to axially support a 100 kN load. If the…

Q: 100 ton of vapor compression refrigeration system using R-134a the vapor entering the evaporator at…

A: Given: The mass of R134a, m = 100 ton The evaporator pressure, Pe = 2 bar The condenser pressure, pc…

Q: Compute for the value of the item required: 1. Vertical Reaction at D 2. Horizontal Reaction at D…

A: Let FG be the force in the member G. Let as represent the weight of the block as "W". ⇒W= 800 lb…

Q: Figure Q2 shows the free body diagram of a 10 m long beam AD of uniform cross-section, simply…

Q: Fill the balks with the correct word/ words a- Water Turbines can be classified into. b- The unit of…

A: As per honour code we are allowed answer first three subparts . For remaining subparts submit a new…

Q: Calculate the final output using the Centroid method for the following strength values Provide step…

A: according to the given details

Q: An aluminum column (0,= 200 MPa) has a length of 8 m. and is fixed at the top and pinned at the…

A: Calculate the moment of inertia of the column about the y-y axis i.e. the vertical centroidal axes.…

Q: Find maximum shear stress Maximum principal stress-8 MPa Minimum principal stress=3 MPa

A: The maximum shear stress is 2.5 MPa.

Q: Determine the magnitude of the load P that wi

A: To find Magnitude of load P

Q: Problem. If the force applied is perpendicular to the handle of the spanner as shown in the diagram,…

Q: The car C increases its speed at the constant rate of 1.8 m/s? as it rounds the curve shown. If the…

Q: *4-60. Determine the magnitude of the moment produced by the force of F = 200 N about the hinged…

A: Find the magnitude of moment of force 200 N about x- axis.

Q: If block B has a leftward velocity of 7 m/s, determine the velocity of cylinder A.

Q: A man is driving his 4.5 m long automobile at 90 kph when the traffic signal in front of him changes…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 6 MPa…

Q: 1.) A Carnot engine is coupled to a Carnot refrigerator so that all the work produced by the engine…

A: Find the heat absorb by the heat engine from the 500K reservoir.

Q: 100 ton of vapor compression refrigeration system using R-134a the vapor entering the evaporator at…

A: Note: As per policy, we can solve the first three subparts. Please resubmit the remaining subpart.

Q: Two furces act 9. the compenent b. the magnitude he angles Gre, Q and Oz the resultant bolt at point…

Q: 3. A square duct of air (p = 1.2 kg/m³; µ = 1.9x104 kg/m-s) is fed from a pressurized tank as shown…

Q: What is the energy produced in MW per month of fuel engine power plant if the maximum demand is…

Q: 1I. Determine the reactions at supports. P-20 kN 98 kN/m 4m 3. 4 m 4 m 3 m

Q: a open cycle and a closed cycle gas turbine engine.

A: Difference between An open and a closed cycle gas turbine engine

Q: 1. A circular furnace has 2 end black surfaces and surface 1 is kept at 500 K and surface 2 is kept…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

a 75.2 MPa

b 54.7 MPa

c 63.1 MPa

d 58.1 MPa

e 69.2 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 4090 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft. O 0.0755 rad O 0.1029 rad O 0.0637 rad O 0.0561 rad O 0.0797 rad
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A hollow steel shaft with an outside diameter of 64 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 2165 N-m. The shear modulus of the steel is G = 80 GPa. Determine the maximum shear stress in the shaft. 85.3 MPa 72.2 MPa 107.2 MPa 115.4 MPa 92.0 MPa
A solid circular steel shaft having an outside diameter of 2.25 in. is subjected to a pure torque of T = 9060 Ib-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. O 3.31 ksi O 5.15 ksi O 4.05 ksi 3.82 ksi O 2.53 ksi
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
The steel shaft is made from two segments: AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G₁ = 10.8 (10¹) ksi (Figure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in. 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. Tmax Submit Provide Feedback IVE ΑΣΦ. 11 | vec Request Answer ? ksi