A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are circular section diameters of 50 mm and 25 mm, respectively. If the normal stress in (1) is 40 MPa. Determine the following:

A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are circular section diameters of 50 mm and 25 mm, respectively. If the normal stress in (1) is 40 MPa. Determine the following:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.10P: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in...

See similar textbooks

Related questions

Q: A bar AB of length L and uniform cross section is attached to rigid supports at A and B before being…

A: Let the bar AB have a uniform cross-section of area = A Drawing the FBD of the bar AB:

Q: A hollow iron pipe with outside diameter of 240 mm is used as a column to carry a load of 80 kN.…

Q: A compression load of P = 55 kips is applied to a 3 in. by 3 in. square post, as shown. Determine…

Q: SIMPLE STRESSES 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable…

Q: Two holes have been formed through a steel bar and a centered axial load is applied as shown in the…

A: Given: P = 32 kN Diameter of hole A = 20 mm Diameter of hole B = 50 mm The steel bar is = 100 x 15…

Q: In a machine shop, the band saw blade is cutting through a work piece that is fed between the two…

Q: 1. Member AC shown in Fig. is subjected to a vertical force of 3 kN. Determine the position x of…

A: Given: The value of the applied load is 3 kN. Average compressive stress at smooth support C equal…

Q: Two aluminum plates, each having a width of b 6.6 in, and a thickness of t-0.700 in, are welded…

Q: The collar bearing shown is subject to a 500 kN force. 500 kN The collar is 25 mm thick. Find d and…

A: Given data: The axial force on collar bearing is F = 500 N. The collar thickness is t = 25 mm. The…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

Q: Two holes have been drilled through a long steel bar that is subjected to a centric axial load as…

A: The maximum stress occurs to the cross-section with the minimum area. (a) The minimum…

Q: A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm.…

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: For P =100 kN, determine the minimum plate thickness t required if the allowable stress is 125 MP

A: Consider the hole A, The radius of the hole is given as, The width of fillet A is given as, Width…

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together. Find the smallest thickness of each…

A: The stress acting between two bodies when they are in contact to each other. It can be called as…

Q: 5.0 in. 3.0 in. The 1.4-kip load P is supported by two wooden members of uniform cross section that…

A: Given load P=1.4 kip Cross section A=5×3 in.2

Q: a. The diameter of the connecting rod CD, given that the normal stress is limited to 140 MPa. b. The…

A: Given: P1= 5 kN Normal stress = 140 MPa To determine: The diameter of connecting rod CD The shear…

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: 8. Obtain a relation for the maximum and minimum stresses at the base of a symmetrical column, when…

A: a) Eccentricity about x-x axis:- As there is eccentric loading so there will be direct stress and…

Q: The lap joint is connected by three 25-mm-diameter rivets. Assuming that the axial load P = 75 kN is…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm…

A: Find the stress at point C and D and also find the value of force Q.

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: An aluminum [E = 10100 ksi] control rod with a circular cross section must not stretch more than…

Q: A vertical force P is applied at a point C located on the axis of sym-metry of the cross section of…

A: The centroid of the column , y=y1A1+y2A2A1+A2 iny=5X6X2+2X4X26X2+4X2 iny=3.8 in

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

Q: Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the…

A: Solution: a) Shear force in each rivet=P4=1204=30kN Since the rivets are in double shear, the shear…

Q: b) The base of a pillar crane, Figure Ql, is fastened to the foundation (a level plane) by twelve…

Q: 4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Given data Diameter of steel shaft = 30 mmAllowable shear stress = 120 MPaAngle of twist = 7°Shear…

Q: Column is manufactured using concrete (E=4.2×10^3 ksi) and reinforcement is done by A-36 steel rods…

Q: 2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the…

Q: A utility hook is formed from a round rod of diameter dinto the geometry as shown below. What are…

A: Consider the diameter (d)= 20mm Refer the table of section formulas, Calculate the radius of…

Q: An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34…

Q: The rigid beam BCis supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm?.…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: QUESTION 2 с Y The 6.7-in diameter steel shaft AB is attached into the rigid wall at C and supported…

A: Given data: ◆ The dia meter of the shaft: d = 6.7 in ◆ The length of the lever AC: x = 3.54 ft ◆ The…

Q: 2.45 A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load…

A: Given that: Diameter of the concrete column is 200 mm. It is designed to carry 320 kN = 320*100 N…

Q: A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress fo the material of…

Q: Q3) A pillar crane, shown in below, is fastened to the foundation by means of 16 identical bolts…

Q: Two identical plates of 63 mm wide and 5 mm thick is connected by a square pin with side dimension…

Q: Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at…

A: Since you have posted question with multiple sub-parts (a), (b), (c), (d), and (e), we solve first…

Q: (a) the normal stresses in the steel plates (1) and the oak block (2). (b) the shortening of the…

Q: Two identical steel [E = 200 GPa] pipes, each with a cross-sectional area of 2600 mm?, are attached…

Q: 1. Two cables A and B had their both ends attached to each other as shown. Cable A is 10 in long and…

Q: The force applied at the handle of the rigid lever causes lever to rotate 0.04 radians clockwise…

A: Find the stress in each cable and force applied at point E.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

P
(1)
B
A
A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are circular
section diameters of 50 mm and 25 mm, respectively. If the normal stress in (1) is 40 MPa. Determine the
following:
The area of Segment (1) is equal to in mm?:
The area of Segment (2) is equal to in mm²:
The axial force (P) is equal to in kPa:
The Normal Stress in Segment (2) is equal to in MPa:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.