A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72-tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive:

Q: pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm…

A:

Q: The following drive system is used to raise a load at constant velocity. The motor rotational speed…

A: (1) Moment of inertia of drum about the output axis, Therefore, Mass of drum is 24 kg. Distance…

Q: Q Two involute gears having module 3 mm and pressure angle 20 mesh externally to give a velocity…

A: "Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: In the gear system shown, the motor applies a torque of 290 N-m to the gear at A. Shaft (1) is a…

A:

Q: The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The…

A:

Q: The lath machine in the university mechanical workshop uses epicyclic gear train shown in Figure 1…

A:

Q: A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and…

A:

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Given: m=8 mmAw=2m=16 mmϕ=20°G=5

Q: The rear wheels of the vehicle are driven by the deferential gear system shown in Figure 2. The…

A: Number of teeth in gear A (TA) = 12 Number of teeth in gear B (TB) = 60 Speed of the gear B (NB) =…

Q: A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and…

A: Data given- Speed of driver = 1000 rpm Tooth of driver = 36 Pitch diameter of driver = 3.609 in…

Q: (c) A rotating load is directly coupled to a motor with moment of inertia Jo, and the load then…

A: Solution:   Both the parts are solved with necessary explanation below:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected…

A: Given: N1=1000 rpmN2=2500 rpmm=12 mmc=600 mm

Q: Q4:- Two shafts A and B in the same straight line are geared together through an intermediate…

A:

Q: A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a…

A: Given: R=99% n_d = 2.5 N_p = 15 N_g = 60 P_d = 6 d_p = 2.50 in. b=1.25 in. n_p = 900 rpm   To find:…

Q: Q4:- An epicyclic gear speed reduction is shown in the Fig. below. The driving shaft carries on the…

A:

Q: A gear train with a ratio of -6:1 and a diametral pitch of 8 is used to reduce the speed from an…

A: P

Q: Problem 3 The gear system shown below has a motor supplying 38 kW at 340 rpm to gear A. Assume the…

A: For solution refer below images.

Q: Two mating spur gears with module pitch 6.5 mm have 19 and 47 teeth of 20° pressure angle and 6.5 mm…

A: Answer: ◆ The number of pairs of teeth in contact: 1.64375 ◆ The angle turned through by the larger…

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: Determine the torque received by the motor shaft running at 4250 rpm, transmitting 11 Hp, through a…

A: To find: The torque received by motor shaft. Given: The speed of shaft is N=4250 rpm. The power…

Q: Q7:- Two gear wheels of module 3 mm and pressure angle 20°, each having 100 teeth. Determine the…

A:

Q: The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O…

A:

Q: A propeller shaft C having a diameter of 75 mm is mounted on two bearings B1 and B2 and is driven by…

A: Helical gear In helical gear the teeth of helical gears are cut in the form of a helix on the pitch…

Q: The lath machine in the Central University of Technology (CUT) mechanical workshop uses epicyclic…

A: Given: The pitch circle diameter of gear D, dz = 214 mm The module of ring gear, m = 4 mm The number…

Q: The lath machine in the Central University of Technology (CUT) mechanical workshop uses epicyclic…

A:

Q: A steel shaft 800 mm long transmitting 15 kW at 400 Q5: r.p.m. is supported at two bearings at the…

A: assumptions :- (1) the pressure angle is 20 degree (2) the shaft is rotating clockwise. FBD....…

Q: A 50 mm transmission shaft transmitting 15 kW power at 200 rpm is supported on two deep grove ball…

A:

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

A:

Q: A steel shaft 800 mm long transmitting 15 kW at 400 r.p.m. is supported at two bearings at the two…

A: First of all lets draw free body diagram for above problem GivenPower transmitted=15kw…

Q: A conveyor is used to drive the inertial load of 0.02 kg m² in the required speed range with a…

A: ◆ The moment of inertia of the load referred to the motor shaft is 0.00133 kg•m2. ◆ The rotation…

Q: A 10" in diameter helical gear carries a torque of 3,000 in-lb. It has 20 deg. Involute stub teeth…

A:

Q: A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle…

A:

Q: involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is…

A:

Q: H.W1 A belt drive system shown, is used as a speed reducer. The input shaft rotates at 2000 rpm and…

A:

Q: (d) A motor drives the winch drum through a reduction gear with a gear tooth ratio of 0.1 as shown…

A:

Q: Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at…

A:

Q: Draw free-body diagrams of the two gears, assuming an input couple M on the OUT X shaft of the…

A: For the gear on shaft AB, For the gear on shaft CD

Q: The gear-reduction unit shown has a gear that is press fit onto a cylindrical sleeve that rotates…

A: The objective is to find the following select suitable tapered roller bearing Given that, Axial…

Q: Problem 3 The gear system shown below has a motor supplying 38 kW at 340 rpm to gear A. Assume the…

A: Given, Power supplied by motor = P = 38 kW = 38,000 W Rotational speed of gear A = NA = 340 rpm…

Q: Q4:- An epicyclic gear speed reduction is shown in the Fig. below. The driving shaft carries on the…

A: Given:ZB=27ZC=30ZD=24ZE=21

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A: Given dataOutput speed = Speed of gear 5 = N5 = 2391 rpmNumber of teeth of gear 5 = z5 = 20For the…

Q: (b) An internal wheel B with 90 teeth is keyed to a shaft F. A fixed internal wheel C with_ teeth is…

A:

Q: The lath machine in the workshop uses epicyclic gear train shown in Figure 1 to operate. Plate gear…

A:

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Gears are used to transmit motion from one shaft to another shaft or between a shaft and a slide.…

Q: (3) A mechanism consists of two flexible shafts: shaft1 and shaft 2 which are connected by gear I…

A: Given data: -  The gear number of gear 1 is N1 = 48. The gear number of gear 2 is N2 = 24. The…

Q: 1,. KB 300 P 579.28N P=1591.55N 300 300 (Machine Design)--- the power transmitted by motor to the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 3. Figure 4 shows a simplified schematic of the drive system of joint 4 of the PUMA 560. The…

A: Given Total coupling stiffness = 200 Nt m/rad Shaft stiffness = 400 Nt m/rad Output stiffness = 2000…

Q: Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh.…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.