Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at locationA to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and T2, where T Is15% of T2.NOTE: This is a multi-part questlon. Once an answer is submitted, you will be unable to return to thispart.T210.018.0"Bearing at O500 Ib12.0pulley diameter = 8.0"75 IbT1pulley diameter = 10.0"Bearing at CSut163 kpslSy117 kpslMaterlal1050 Q and TUsing the DE-Goodman criterla and a design factor of 1.5, calculate the diameter based on the shaft's loadings and yourguess for the shaft's dlameter at the critical location. What Is the shaft diameter? Assume the notch radlus to be 0.02In. (You must provlde an answer before moving to the next part.)The shaft dlameter Is|1.3146| In.The factor of safety agalnst ylelding Is3.75

Answered: Image /qna-images/answer/c0f9f7cb-37ec-48e1-9c0b-fcfc000e7661.jpg

Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and 72. where T, is 15% of T2. NOTE: This is a multi-part question. Once an answer Is submitted. you will be unable to return to this part. T2 10.0 18.0 Bearing at o 500 Ib 12.0 pulley diameter = 8. 75 Ib T1 pulley diameter = 10.0 Bearing at C

Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and 72. where T, is 15% of T2. NOTE: This is a multi-part question. Once an answer Is submitted. you will be unable to return to this part. T2 10.0 18.0 Bearing at o 500 Ib 12.0 pulley diameter = 8. 75 Ib T1 pulley diameter = 10.0 Bearing at C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A straight spline has 10 splines and is Fit B. The required major diameter, D, of this spline subject to a torque capacity per inch of length of spline of 600 lb-in is most likely: O 0.8 in O 2 in O 1.4 in O 1.7 in
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
For the given ball bearing find out the dynamic load value when the Equivalent load is 14836.2N and the Life of the bearing is 1238x10 revolutions. O a. 159305.06 O b. 139227.09 O c. 169418.59 O d. 80407.14 Finish attemp hp
topic: torsion in circular shafts The hollow shaft used in the system has the following conditions: Outer diameter (Ø): 150 mm Ø Allowable Shearing Stress: 85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
A shaft turning 200 RPM is to drive another shaft at 250 RPM connected in open belt. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 3500 FPM.
! Required information A torque T-130 N-m is applied to the shaft EFG, which is running at constant speed and contains gear F. Gear F transmits torque to shaft ABCD through gear C, which drives the chain sprocket at B, transmitting a force Pas shown. Sprocket B. gear C, and gear F have pitch diameters of a = 120 mm, b= 200.004 mm, and c= 100 mm, respectively. The contact force between the gears is transmitted through the pressure angle = 20°. 25 DEKO d-30mm 1-250 man 0 30 x-125+ The maximum principal normal stress is The maximum shear stress is Combine these stresses and determine the maximum principal normal and shear stresses in the shaft. MPa View ad MPa.
A taper roller bearing used in a windmill has a dynamic load capacity of 26 kN. The desired life for 90% of the bearings is 8490h and the speed is 350 rpm. The rated bearing life(L10) in millions of revolutions is . O a. 509.40 O b. 178290.00 O c. 17829.00 O d. 178.29 In a machine, the maximum torque transmitted by a shaft exceed by 23 % the actual torgue. A power of 3 kW has to be transmitted to another unit at a speed of 650 rpm. What should be the value of Maximum torque ? The maximum torque transmitted in N-m, When a component is subjected to fatigue loading, the endurance limit is the criterion for failure Select one: O True O False If "g" is the notch sensitivity, K, fatigue stress concentration factor, and k, the theoretical stress concentration factor. Identify the correct relation relating to these factors. (Ke-1)+(q)=(Kf - 1) O b. (K-1)=(Kf -1)*q O a. O c. (K-1)*(q)=(Kf -1) O d. (K,-1)-(q)=(Kf -1)
The width of the belt used if its thickness is 6 mm. Ans. 261 mm 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt speed of 25 m/s. The belt has a mass of 2 kg/m of the belt length. The belt is used in a crossed configuration to connect a 300 mm diameter driving pulley to a 900 mm diameter driven pulley at a shaft spacing of 6 m. A. Calculate the belt length and the angles of wrap. Ans. 13.95 m, 3.34 rad or 191.4° B. Compute the belt tensions based on a coefficient of friction of 0.33. Ans. 1.76 KN, 1.96 KN
Draw schematic figures and find max./min. diametrical slip / press mouth for the following four shaft / sleeve combinations: 1 ø150 H7 / m5 2 ø100 H7 / r6 3 ø80 H7 / g5 4 ø50 H7 / f7
Homework Verify the value of the constant, 63 000 for the following equation in order to have the torque in lb.in units. T = 63000 P n ……………... (3-6)
2. A 101.6 mm diameter shafting SAE 1040 grade, cold rolled, having a yield point of 60 ksi and 2/3 x 8/10 x 5 inches key. Compute the minimum yield point in the key in order to transmit the torque of the shaft. The factor of safety is 2. a. 92.45 kPa b. 92.45 ksi c. 94.25 ksi d. 94.25 kPa
Assignent no 1 Qt+ A Compound gear 6 Jears. No of teeth; train Consists of A B D 60 40 35 २४ 50 30 shaft on another shaft. The Gears B ş C are on one while are gears Gear A drives c drives gear D B, gear gear S gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2+ State advatages of Cycloidal In volute profile as a gear tooth pnfile.