A vertical gap of 0.1 mm contains a fluid of viscosity (2 Pa.s). A thin metallic plate sheet (0.2 m x 0.3 m) is to be lifted up with a constant velocity of 0.1 m/s through the gap. Find the force (f) given the weight of the plate is 60 N a) If the plate is in the middle of the gap b) If the plate is as shown below

A vertical gap of 0.1 mm contains a fluid of viscosity (2 Pa.s). A thin metallic plate sheet (0.2 m x 0.3 m) is to be lifted up with a constant velocity of 0.1 m/s through the gap. Find the force (f) given the weight of the plate is 60 N a) If the plate is in the middle of the gap b) If the plate is as shown below

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two plates are placed at a distance of 15 mm apart. The lower plate is fixed while the upper plate having surface area of 1.0 m^2 is pulled at 0.30 m/s. Whar is the force in Newton required to the speed if the fluid separating them is having viscosity of 1.5 poise?
O Q1. Given the following system, find the shear stress in kg/m², developed on the fixed plate. The kinematic viscosity of the fluid is 4.4x104 m²/s and the specific weight of the fluid is 1.62 t/m³. y U 3 = 1.5- 0.5 (2) U h fluid U= 12 cm/s, h= 22 cm fixed plate
Two plates are placed at a distance of 15 mm apart. The lower plate is fixed while the upper plate having surface are of 1.0 m^2 is pulled at 0.30 m/s. The force in Newton required to the speed if the fluid separating them is having viscosity of 1.5 poise is.
Two plates are placed at a distance of 0.15 mm apart. The lower plate is fixed while the upper plate having surface area 1.0 m² is pulled at 0.3 m/s. Find the force and power required to maintain this speed, if the fluid separating them is having viscosity 1.5 poise.
A tank is filled with fluid under prcssurc anti the prcssurc gauge fixcd at the top indicatcs a prcssurc of 21 kPa. The curved surfacc of the top is quarter of a circular part of radius 2.6 m. calculate the magnitude (N) and direction (degree) of the resultant force on the cun'ed surface. (p=950kg./m³for fluid)
plz help me with this one i would appreciate it if you help me now A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that has a diameter of 1 m that filled with oil that has a viscosity of 8x10-3 N.s/m2 What is the shear force that acts on the circumference of the piston (N)? Assume the variation in velocity of the oil is linear.
a flat plate of area 1.5×106 mm 2 is pulled with speed of 0.4 m/s relative to another plate located at a distance of 0.15 mm from it. find the force required to maintain this speed, if the fluid separating them is having viscosity 1 poise
Two plates are separated by 30 mm space. The lower plate moves at velocity of 2 m/s while the upper plate moves at a velocity of 8 m/s. Oil (S-0.84) which fills the space. The oil viscosity is equal to 0.003 m /s. The variation in velocity of the oil is linear. What is the shear stress in the oil (N/m2)? upper plate 8 m/s 30 mm OIL 2 m/s lower plate Lenovo K9 Note AI Dual Camera
A shaft of radius R, is held concentric within a sleeve of radius R2. If the shaft is stationary while the sleeve moves with an axial velocity of vo. The pressure gradient in the direction of motion is assumed to be zero (i.e., 2 = 0). Constant viscosity and density are assumed. Inertia and body force terms are neglected. Also, the velocity varies in the r direction only (i.e., v, = f(r)). %3D dz %3! a) Define the appropriate Navier-Stokes equation. b) Determine the velocity (v:). c) Determine the volume flow rate. d) Also, what is the friction force per unit length on the sleeve? R
3) The viscosity of the Newtonian fluid with a density of 650 kg/m³ is determined with a viscometer as shown in the figure below. The required torque (T=F.r) applied to the inner cylinder (r¡ = 4 cm) to rotate with an angular velocity of 6 rad/s is 3x10-7 Nm. If the velocity distribution in the clearance between the cylinders is linear, a) Find the viscosity (µo) of the fluid b) Find the shear stress on the side surfaces in the viscometer if the viscosity varies according to µ= H0 (1-r/r2) where r2 = W=6rad/s 2cm 150mm ri+2 (cm) due to heating during rotation. .fluid
The space between two parallel plates 0.001 ft apart is filled with oil viscosity 0.7cp. The top plate is stationary while the lower plate is moving in the x-direction with a velocity 1ft/sec. A. Determine shear rate B. What should be the shear stress in lbf/ft^2? Answer asap pls
A flat plate of area 2x10¹ cm² is pulled with a speed of 0.5 m/s relative to another plate located at a distance of 0.2 mm from it. If the fluid separated the two plates has a viscosity of 1.0 poise, find the force required to maintain the speed.