Determine the shearing stress acting at joint C with a pin diameter d of 46 mm if a vertical force of F = 24 kN is applied at joint B using the figure below. Member AB has a cross-sectional area of 0.006 m² and member BC has a cross-sectional area of 0.005 m². The distance between joints A and C is 8.7 m, and the distance between joints A and B is 10.0 m. Answer directly. 41 Fc

Determine the shearing stress acting at joint C with a pin diameter d of 46 mm if a vertical force of F = 24 kN is applied at joint B using the figure below. Member AB has a cross-sectional area of 0.006 m² and member BC has a cross-sectional area of 0.005 m². The distance between joints A and C is 8.7 m, and the distance between joints A and B is 10.0 m. Answer directly. 41 Fc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
A link is loaded as shown, it is attached with two bolts with a diameter of 0.25 in. The link width is 2 lh and its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts) determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the bolt holes. 2 in G
The T-bracket is formed by welding together two cylindrical rods AB and CD. If the allowable shear stress is 80 MPa, what is the smallest allowable diameter of rod AB? Neglect the stress caused by the transverse shear force
The lap joint is fastened with four ¾-inch diameter rivets. a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. c. what is the maximum value of the load P (kips) that can be applied to the joint?
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 18 mm and the diameter of rod (2) is d₂ = 31 mm. Determine the absolute value of the normal stress in rod (2). 140 KN 80 KN (2) 140 KN A O 342 MPa O 368 MPa O 313 MPa O 281 MPa O 265 MPa B
The lap joint is fastened with four ¾-inch diameter rivets. ➢ a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ c. what is the maximum value of the load P (kips) that can be applied to the joint?
06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm
2-2. mechanism must transmit a tensile force of 5 kN A steel rod 10 m long used in a control without stretching more than 3 mm, nor exceed- ing an allowable stress of 150 MN/m². What must the diameter of the rod be? Give the answer to the nearest millimeter. E 210 000 MN/m2.
Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 15 ksi, and the shearing stress in the pin must not exceed 21 ksi. When the hoist is in the position given by: a = 44 in b = 11 ft c = 19 ft find the following: (a \& b) The forces carried in ropes AB and BC (c l& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013 Michael Swanbom (a) TAB = (b) TBC = (c) dAB = (d) dBc = (e) d =
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End A is subjected to a vertical force P and a horizontal force Q. Use P = 90 N and Q = 70 N. a. Determine the internal axial force (in N) in section B. b. Determine the internal shear force (in N) in section B. c. Determine the internal torque (in N-m) in section B. With FBD please thank you.
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft