A voltage is given by v(t) = 10 sin(1000TTt-30°). Find the amplitude (A), frequency (f), Phase angle (P), Time Period(T). A = 10, f = 500 Hz, P = -60°, T = 2x10-3 sec A = 10, f = 500 Hz, P = -120°, T= 2x10-3 sec A = 10, f = 1000TT Hz, P = -120°, T = 2x10-3 sec A = 10, f = 1000TT Hz, P = -60°, T= 2x10-3 sec

A voltage is given by v(t) = 10 sin(1000TTt-30°). Find the amplitude (A), frequency (f), Phase angle (P), Time Period(T). A = 10, f = 500 Hz, P = -60°, T = 2x10-3 sec A = 10, f = 500 Hz, P = -120°, T= 2x10-3 sec A = 10, f = 1000TT Hz, P = -120°, T = 2x10-3 sec A = 10, f = 1000TT Hz, P = -60°, T= 2x10-3 sec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If Vin is a source with a 10V sinusoidal signal of 10kHz, R is 500Ω, and C is 0.05µF what will the steady state sinusoidal voltage be? What is the phase offset? What is the voltage immediately after the source is connected (unknown phase)?
The magnitude is nonnegative. If the amplitude of a sinusoid is given by a negative number, the negative number is converted to a positive magnitude, and a phase of O a. 90 O b. 45 O c. -90 O d. 180 or -180 degrees.
can you please give me the comple solution for this question, thanks. A certain voltage function contains a constant term, a fundamental and third harmonic. The maximum value of the fundamental is 85 % of the constant term and the maximum value of the third harmonic is 55 % of the constant term. If the effective value of this function is 180.3V, find the magnitude of the two harmonics. A.IstHarmonic = 75 V , 3rd Harmonic = 120V B. Ist Harmonic = 80 V , 3rd Harmonic = 125V C. IstHarmonic = 120 , 3rd Harmonic = 75V D. Ist Harmonic = 125 V , 3rd Harmonic = 80V E. NOTA
R C Vs Vo If there is a unit step function at the input of the circuit above and R=24 and C=1/24, which of the following statements is incorrect for the output waveform? a. There are positive and negative alternans (half regions) in the output wave. b. Its amplitude is "1". c. The output is in triangular waveform. d. There is a 180 degree phase difference between the input and the output. www w e. At t=0 there is a unit impulse (impulse) sign.
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 16 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is doubled? Select one: O 16 Vrms 32 Vrms O 8 Vrms . 8 Vrms ..... O 5.657 Vrms 5.657 Vrms ....... O 8 Vrms . 16 Vrms O 16 Vrms 8 Vrms ......
R=1 ka A Oscilloscope V-5 V f=500 Hz In the given circuit, a sinusoidal signal is applied at the source, current measured by AVO meter is 0.01A (RMS) and voltage measured by oscilloscope is 25mV(peak). What is the capacitance value of capacitor? Lütfen birini seçin: a.1 uF b.0.18 mF c.0.15 mF d.0.1mF e.0.12 mF
The rms value of the resultant current in a wire carries a dc current of 10 A and a sinusoidal alternating current of peak of value 20 A is-
An alternating current has an rms value of 50A and a frequency of 60HZ.Find the time taken to reach 50A for the first time.
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 10 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is reduced to the half value? 3.536 Vrms . 3.536 Vrms O 5 Vrms . 1.7677 Vrms O 3.536 Vrms. 1.7677 Vrms O 5 Vrms . 5 Vrms ...... O 10 Vrms . 10 Vrms ......
Question 1 Given the two sinusoidal waveforms, f(t) = -50coswt - 30sinwt and g(t) = 55coswt - 15sinwt. Find the phase angle by which f(t) leads g(t) %3D ANSWER fit) leads g(t) by Blank 1
Apply a sinusoidal input voltage with 2V p-p and vary the frequency according to the table below. Measure the voltage Vr and current I from the voltage across R and find the phase angle between the Vi and I.
Determine V, in the circuit in the figure below. 20 -j10 j2n 11/6 v (+ 2/0° A 5/0 v + Enter (a) the amplitude and (b) the phase angle. The phase angle must be in the interval (-180°, 180°]. (a) V (b) degrees 2.