a. A steel rod of 1 cm in diameter projects (4+R) cm from the wall as shown in figure 1. If the rod is deflected by 0.222 mm from its original position, find the shearing force (F) applied to the rod. Consider the Shearing Modulus of steel is (R + 8.27) × 101ºPa. Wall L R=30 ΔL F Figure 1

a. A steel rod of 1 cm in diameter projects (4+R) cm from the wall as shown in figure 1. If the rod is deflected by 0.222 mm from its original position, find the shearing force (F) applied to the rod. Consider the Shearing Modulus of steel is (R + 8.27) × 101ºPa. Wall L R=30 ΔL F Figure 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.19P: During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as...

See similar textbooks

Related questions

Q: A load P is supported by two springs arranged in series. The upper spring has 20 turns of 20-mm…

Q: a beam has a rectangular cross section of heigh 300mm and width 60mm. In one cross section plane the…

Q: a. A steel rod of 1 cm in diameter projects (4+R) cm from the wall as shown in figure 1. If the rod…

A: Givend=1cm=0.01mL=4+R∆L=0.222G=R+8.27×1010PaAskedF=?

Q: degree is the angle of twist of a solid rod of length 50 cm and diameter of 25 mm, when it is…

Q: An alumin um rod with the rod axis oriented in the z-direction is subjected to T20 = 10MPa, which is…

Q: Figure 1: y P = 400 kN 30° 1000 mm A Area 30 mm 20 mm In Figure 1, the equilibrium shear force…

A: Given data :- force = 400KN find the shear force at point A.

Q: Determine the maximum shearing stress is T=40 kN-m. TABLE 3.1. Coefficients for Rectangular Bars in…

Q: Determine the maximum shear force in kN in the figure below. 16 kN | 4 kN/m 20 kN 2 kN/m A D

Q: maximum deformation of aluminum wire is 0.15 cm maximum deformation of steel wire is 0

Q: aluminum tube with the cross section shown has a constant wall thickness of 2 mm. A torque T = 400…

Q: A hollow shaft with outside diameter of 135 mm and wall thickness of 8 mm transmits 182 kW at 400…

A: L=5m 1psi= 6894.76 N/m2

Q: The torsional deformation of a steel shaft is to be 1° in a length of 600 mm. The design shear…

Q: A steel shaft 'A' of diameter 'd' and length 'I' is subjected to a torque T Another shaft 'B' made…

A: Normal stress is defined as the intensity of force exerted over a unit cross sectional area which…

Q: A circular rod made of aluminum with a radius of 32.5 mm was placed in a steel tube with a length of…

A: Given data, rAl = Radius of the aluminum rod = 32.5 mm L= Length of the rods = 2.4 m = 2400 mm rs,i…

Q: A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when…

Q: Calculate the displacement of B-D-F points using the energy method or the Castigliano method. Cross…

Q: A horizontal aluminum rod 2.5 cm in diameter projects 4.5 cm from a wall. A 1000 kg object is…

A: Given data: d=2.5 cmL=4.5 cmm=1000 kgG=3×1010 N/m2 Need to determine the shear stress on the rod and…

Q: a. A steel rod of 1 cm in diameter projects (4+R) cm from the wall as shown in figure 1. If the rod…

A: Write the given data: Understand the following figure for the given beam.

Q: Determine the torsional stiffness of a solid aluminum shaft of length 2 m and radius of 30 cm. The…

Q: 12. A cold drawn steel rod of circular cross-section is subjected to a variable bending moment of…

Q: If an isotropic material has a shear modulus of 30 Gpa and a Poisson's ratio of 0.34, calculate its…

Q: 1. A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and…

A: This question is related with the pure torsion equation.

Q: 1. A flanged bolt coupling consists of eight 12 – mm diameter steel bolts on a bolt circle of 300mm…

A: Given details: d1=12 mmd2=10 mmn1=8n2=6ζ=55 MPaR1=150 mmR1=100 mm Note:According our guidelines I…

Q: If an isotropic material has a shear modulus of 27 Gpa and a Poisson's ratio of 0.42, calculate its…

Q: A shaft with a length of 2 m has the cross section shown in Figure 1, where a = 4 cm and t = 4 mm.…

A: Torque Torque is a rotational equivalent of linear force. Torsion Torsion is the twisting of an…

Q: P1. A uniformly tapering circular rod is subjected to load as shown in the figure . Determine the…

A: When an axial load is applied to a bar it tends to get deformed. This elongation depends upon the…

Q: 3. Shafts AB and BC (each 50 mm long) are welded to each other. Shaft AB is hallow with 20 mm inner…

A: Given data: The outer diameter of the shaft AB is DAB=30 mm The inner diameter of the shaft AB is…

Q: A solid transmission shaft is 88.9 mm diameter. It is desired to replace it with a hollow shaft of…

Q: a) Find the twist angle of the free end. b) Find the shear center of the cross-section. The material…

A: Shear center : it is the point of application of the resultant shear stress, i.e., the point at…

Q: A 24 mm diameter shaft 0.8 m long is twisted through an angle of 1.8 degrees. What is the stress…

Q: yauges system mounted at a point on a structural member that is subjected to multiaxial stresses,…

Q: A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P =…

A: Given Data: L=600 mm=0.6m d=20 mm=0.02m so, Area=πd24=π4×0.022=3.1415×10-4m2 P=50…

Q: Compute the torsional deflection in degrees of a 110 mm diameter, 1.4 meter long shaft subjected to…

A: GIVEN DATA- D=110mm T=3*10^6Nmm G=83000 N/mm2 WE HAVE TO CALCULATE TORSIONAL DEFLECTION IN DEGREE

Q: A shaft is subjected to an axial pull of 20N and transverse shear force of 10kN The yield strength…

A: Given: Pt1 =20 KN, Ps = 10 KN, σy = 250 MPa , μ =0.3 diameter of shaft, d =? cross…

Q: The two cylindrical rod segments shown in the figure below (Figure 1) are fixed to the rigid walls…

A: Find the new length of aluminum segment

Q: An external pressure of 10 MPa is applied to a closed-end thick cylinder of internal diameter 160 mm…

A: External pressure P= 10 Mpa Di = 160 mm ;r = 80 mm Do = 320 mm ; R =160 mm σcmax = 30 Mpa E = 207…

Q: A 2-inch line shaft is transmitting 20 hp rotating at 200 rpm, carrying two pulleys spaced 30 inches…

Q: A 10 m length shaft is used to transmit 50 kw power at 450 rpm. If the shaft stress is limited to 40…

A: Given Length, L = 10 m Power, P = 50 kW Speed, N = 450 rpm Stress = 40 MPa Find…

Q: A 2m long rod of radius 1 cm which is fixed from one end is given a force of 8 N. Calculate the…

A: Given data: The radius of the rod is R = 1 cm. The force is F = 8 N. The elastic constant is E =…

Q: A rod of diameter 42 mm and 51.5 cm long having the modulus of elasticity is 286 MPa. During loading…

Q: The bars shown in Figurehave equal cross-sectionalareas and they are each subjected to a torque of…

Q: A shaft with a solid, circular cross section consisting of two segments isshown in parta of the…

Q: A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length.…

A: Givend=6mmdecrease in lenght ∆L=3.96%×LG=602 Mpaμ=0.20

Q: The strain of a component, which has a tensile modulus of 4 X 105 MPa, and subjected to a stress of…

A: Given data :- Modulus of elasticity = 4 X 105 MPa Stress = 6000 kpa = 6 mpa Find :- Strain = ?

Q: We have an assembly with a steel rod AB and an aluminum BC, each having a cross sectional area shown…

Q: shaft is subjected to an axial pull of 22N and transverse sheer force of 12KN The yield strength of…

A: Given: Axial load (P)=22N (Check the value is N or KN again)Transverse shear force (F)=12kNYield…

Q: We have an assembly with a steel rod AB and an aluminum BC, each having a cross sectional area…

Q: (2) The strength condition of composition of bending and torsion is _M₂_ √ M² + (aT)² ≤ [0_16] J.= W…

Question

100%

a. A steel rod of 1 cm in diameter projects (4+R) cm from the wall as shown in figure 1. If the rod is
deflected by 0.222 mm from its original position, find the shearing force (F) applied to the rod. Consider
the Shearing Modulus of steel is (R + 8.27) × 101ºPa.
Wall
L
R=30
ΔL
F
Figure 1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a point in an elastic material under strain, the stresses on the three mutually perpendicular planes are as follows:A normal tensile stress of 60 N/mm^2and shear stress of 40 N/mm2 on one plane and a normal tensile force of 40 N/mm^2and a complimentary shear stress of 40 N/mm^2 on another plane. Find the following using Mohr circle only (take 5 N/mm2 = 1 cm)a. The principal stresses and principal planes.b. The maximum shear stress and its plane.c. The normal and shear stress on a plane inclined at an angle of 30Oto major principal plane.
1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b Ay r r=2acose Figure 1: Circular shaft with a keyway. The keyway is represented by the boundary equation r = b and the shaft is represented by the boundary equation r = 2a cos 0. Show that using a Prandtl stress function of the form ²) (₁ (1-2a cos) X v = K (b² − ²) (1 – : will solve the problem of torsion on this shaft and find the constant K (assume an applied torque T). Compute the shear stress components Txz and Tyz. (Hint: start by converting the stress function to Cartesian coordinates).
A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube is r1 = 45 mm and the measured angle of twist betweenthe ends is 0.5°, what is the shear strain γ1 (in radians) at the inners surface? b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to bekept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius(r2)max?
An aluminum rod with the rod axis oriented in the z-direction is subjected to T20 = 10M Pa,which is below the shear yield strength. The shear modulus of aluminum is 26 GPa. Which of the following is the resulting tensor shear strain? 1.92E-4 U 3.85E-4 6.77E-4 O 5.52E-4
Determine the maximum value of Qof the Transverse Shear Stress formula [T = (VQ)/(It)] at point p in mm for the rectangular section shown in Figure 5.2c. Given h = 329 mm and B = 227 mm. h e B – Figure 5.2c Type your answer..
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to the magnitude of the minimum shear strain developed on that section? Select one: O A. 0.0072 rad O B. 0.0137 rad O C. 0.0128 rad O D. 0.0067 rad
Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected to the loading shown. Determine the normal stresses and shearing stress at point H shown at the rod. 250 mm -H- 150 N 150 mm 4 cm 300 N 200 N
Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C that can resist a moment. (Image taken from Statics and Mechanics of Materials by Beer, Johnson, DeWolf and Mazurek) T₁ = 300 N-m 30 mm TB = 400 N-m 46 mm 055 Shear Stress in AB = Shear Stress in BC= B 0.9 m 0.75 m units: units:
The state of stress in a body is uniform and is given by: 0xx = 3MPa; Txy = 2 MPa; Txz = 4MPa Oyy = 5MPa; Tyz = OMPa; ozz 2MPa = a. Determine the principal stresses and their corresponding eigenvectors (work must be performed by hand) b. Determine the stress vector on a plane oriented at nx=.707, ny=.707, n₂=0 c. Determine the normal stress on the plane given in item (b)
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
1.5 kN 120 mm Outer diameter: 72 mm Inner diameter: 62 mm 150 mm D 120 mm 4.5 kN A For element A find: (a) Torsional shearing stress (b) Transverse shear stress (c) Normal stress Q = [AS] × y 2rm TU y =
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section