The bars shown in Figurehave equal cross-sectionalareas and they are each subjected to a torque of (T = 160 N-m). Determine:(a) the maximum shear stress %3D in Bar (a).Assume G 28 GPa. * %3D (b) (a) 30 mm 50 mm 25 mm 15 mm O104.6 MPa O 39.0 MPa O 78.0 MPa O52 3 MPa

The bars shown in Figurehave equal cross-sectionalareas and they are each subjected to a torque of (T = 160 N-m). Determine:(a) the maximum shear stress %3D in Bar (a).Assume G 28 GPa. * %3D (b) (a) 30 mm 50 mm 25 mm 15 mm O104.6 MPa O 39.0 MPa O 78.0 MPa O52 3 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A propeller shaft for a small yacht is made ofa solid steel bar 104 mm in diameter. The…

A: (a) Write the given data. d=104 mmθL=2.083.5G=80 GPa

Q: 3.13 The torques T and 2T are carried by a shaft consisting of steel and aluminum segments. If the…

A: Given:ζs=14,000 psiζa=7,500 psiθmax=8Gs=12*106 psiGa=4*106 psi

Q: 1. A shaft system ABC consists of a solid bar AB welded to a hollow bar BC. The shaft is subjected…

Q: Two sections of steel drill pipe, joined bybolted flange plates at B, are subjected to a…

A: Calculate the total load due to the uniformly distributed torque on the part BC in the pipe. T0=50…

Q: A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800…

Q: The thin walled cross-section, shown in figure, has an allowable shear stress of 2 ksi. Determine…

A: FOR THIN WALLED, τ×t=T2AA=MEAN AREA L=4-2×0.122=3.88inB=2.5-2×0.22=2.3inA=L×B= 3.88×2.3=8.924in2

Q: Q2 A solid circular bar ABC consists of two segments, as shown in figure 2. One segment has diameter…

A: The diameter of the shaft can be determined by two criteria 1) Shear stress 2) Angle of twist Both…

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: 4 kN m 1.5 kN m Aluminum Steel Bronze B 100 mm 75 mm 3m 2 m 1.5 m- C FIG. P3.12 FIG. P3.11 3.12 The…

A: For solution refer below images.

Q: When a steel rod below is subjected to torque (T = 3 kN m) and bending moment (M = 2 kN m)…

A: Write the given data with suitable variables. M=2 kNmT=3kNmd=50 mm

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Data given- d = 100 mm σaxial = 50 MPa T = 10 kN-m

Q: 4- A 4m long solid circular steel shaft is fixed at one end, and subjected to a twisting torque of…

Q: A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft…

Q: Figure 2: cylindrical shaft

Q: 8. A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the…

A: Calculate the torque in segment AB. Calculate the torque in segment BC. Calculate the torque in…

Q: A stepped shaft ABCO consisting of solid circular segments is sublected to three torques, as shown…

Q: Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the…

A: Given The radius of steel wrench is r=0.4 cm. The length of steel wrench is l=0.200 m. The…

Q: 6. A propeller shaft in a ship is 350 mm in diameter. The allowable working stress in shear is 50…

Q: A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is…

Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…

Q: 2. A solid steel rod with a diameter of d = 50mm is subjected to a bending moment M = 1.5 kN-m and a…

Q: Lets consider a solid circular shaft having a diameter D = 40 mm subjected to a triangular…

A: Given: The diameter of solid circular shaft, D = 40 mm The torque acting on shaft, t = 100 N.m/m The…

Q: 500 lb • ft Aluminum Steel Bronze 1.0 in. 2 in. $1.0 in. B 6 ft 4 ft 3 ft rIG. P FIG. P3.22 3.22 The…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

Q: Problem 3.15. A hollow aluminium tube of rectangular cross- section as shown in Fig. 3.27 is…

A: We know that a hollow aluminum tube with a rectangular cross section is subjected to a torque of…

Q: A hollow aluminum tube used in a roof structure has an outside diameter of 104 mm and an inside…

A: Given data: τ=48 MPaD=104 mmd=82 mmL=2.75 mG=28 GPa Need to determine the angle of twist.

Q: An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress…

A: Given Data Diameter of bar AB is : d1=90 mm Diameter of bar BC is : d2=60 mm Allowable stress is :…

Q: A hollow steel shaft with an outside diameter of 64 mm and a wall thickness of 5 mm is subjected to…

Q: 2. A tube is made of aluminum ( G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 10 N/mm² and length of…

A: Given data as per question shaft dimeter =125 mmPower transmitted =120 kwSpeed=160 rpmC = 8×10…

Q: 1.5 kN m 4 kN m Steel Aluminum Bronze 100 mm 75 mm 3 m 2 m -1.5 m- C FIG. P3.12 FIG. P3.11 3.12 The…

A: Answer: (a) Maximum shear stress in each material : ◆ Aluminum : 28.0 MPa. ◆ Steel and Bronze :…

Q: Q- A solid 75-mm-diameter Aluminum [E = 80 GPa and 0.3 Poisson ratio] shaft that is 1.25-m long…

A: DAl=Diameter of Solid Aluminum=75 mmLAl=length of Aluminum shaft=1.25 m DB1=Outside Diameter of…

Q: A Compound Steel (G=80GPA) Shaft consists of a solid 90mm diameter (segment1) and a solid 70mm…

Q: 2- Compare the weight of equal lengths of hollow and solid shafts to transmit a torque T for the…

Q: Q4-A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: 2 PUII The figure below shows a shaft of three segments. It is restrained (fixed support) at both…

Q: 4) The thin walled cross-section, shown in figure, has an allowable shear stress of 2 ksi. Determine…

Q: A compound bar consists of a steel and bronze segment (Gs t= 80 GPa and Gbr = 40 GPa), The limiting…

Q: 35 mm 10 kN-m 2.36 x10° mm* G1 = 70 GPa (1) 40 mm C2 = (2) 4.02 x106 mm B 45 GPa 2800 mm 3600 mm A…

A: GIVEN DATA- A COMPOSITE SHAFT GIVEN C1=35mm J1=2.36*10^6 mm^4 G1=70GPa C2=40mm J2=4.02*10^6 mm^4…

Q: A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ…

Q: A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques…

Q: Two sections of steel drill pipe, joined by bolted flange plates at 8, are subjected to a…

Q: A hollow steel shaft with an outside diameter of 76 mm and a wall thickness of 5 mm is subjected to…

Q: A solid brass bar of diameter d =1.25 in. issubjected to torques T1, as shown in part a of the…

A: d=1.25Applied troque on the solid bar be T1Allowable shear stress in the brass τa=12ksiPolar moment…

Q: 500 lb • ft Tc Aluminum Steel Bronze A 1.0 in. 2 in. +1.0 in. 6 ft 4 ft + 3 ft rIG. P FIG. P3.22…

Q: A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of…

A: Answer: The correct answer is option (b) i.e. 12.57 ksi.

Q: The shaft of a heavy-duty tractor transmits 120 kW at 600 rpm, and at the same time supports a load…

Q: A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the…

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 12.25 in. and…

A: Given data: d1o=12.25 int1=0.365 ind2o=5.5 int2=0.28 inTB=69 kip-ftTC=12 kip-ft Need to determine…

Q: Q-A solid 75-mm-diameter Aluminum [E 80 GPa and 0.3 Poisson ratio] shaft that is 1.25-m long extends…

Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 240…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

material exam
strength of materials exam
IpQLSe0S4jiBdFukwD10EDn6YcB3b9pFVy9DyHocjzQq4hz4Q1SGw/formResponse
ews
Translate
The bars shown in Figurehave equal cross-sectionalareas and they are each
subjected to a torque of (T = 160 N-m). Determine:(a) the maximum shear stress
in Bar (a).Assume G = 28 GPa. *
(b)
(a)
30 mm
50 mm
25 mm
15 mm
104.6 MPa
39.0 MPa
78.0 MPa
52 3 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
1 %YY . 1:1. 1 docs.google.com Q بريدك الإلكتروني A vertical shaft is supported by a 5 نقاط thrust collar and bearing plate, as shown in Figure. Calculate the maximum axial stress of the shaft if the average punching shear stress in the collar and the average bearing stress between the collar and the plate are limited to 100 and 125 MPa, .respectively F100 mm- 150 mm Collar 25 mm إضافة ملف یالا - غرف الدردشة المجانية )aD( الصوتية المجانية: الدردشة الحية مع أصدقائك II
Question 3: The 60 mm diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimun shear stresses on the outer surface of the shaft and specify their locations, measured from the fixed end A. Take : AA= 1.6 BB = 0.9 CC = 1200 AN/ m 2 kN-m/m AA m CC Nm B вB m Solution : = CC N-m TAB CC N-m 2o0ox N.m CC N.m
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows : F, = 1590 N; F, = 580 N Pulley Gear F1 A D F, -100 : 200- 100→ All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.
P= 200 lbs |=2" T 250 in-Ibs Qt. DRAW STRESS STATES いITH A SQLARE ECEMENT エN xY AXES Label with stress values Q2 DRAW MOHR'S CIRCLE AT A Q3.CALCULATE PRINCIPAL STRESSES AND DRAW THE PLANE FoR ri$ a IN THE SCHEHATIC Draw element rotated to principal planes and label with stress values and rotation angle
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
Let's consider a solid circular shaft subjected to the torque loads as shown Determine the minimum required diameter "D" if the shaft is made of a material having a yielding shear stress Ty = 100 MPa, for a factor of safety FS = 2. The polar moment of inertia of a solid circular cross-section is given by Jr.R¹/2. 300 mm B 600 mm 100 N.m 500 N.m 600 mm 400 N.m
Problem 7 A 12-inches square steel bearing plate lies betw een an 8-inches diam eterw ooden postand a concete footing as show n in Fig.P-110.Determ ine the m axim um value of the bad P if the stress in w ood is lim ited to 1800 psiand that in conarete to 650 psi 8 in Bearing Plate 12 in 12 in Figure P-110
Figure shows a hollow quarry drill bit in operation. When drilling, it experiencesresistive torques T1 = 10 kNm at A, T2=26kNm at B. A pushing compressive force (in x direction)is also applied 25 kN at C generating a compressive stress σxx in AB and BC. The hollow part of the drill bit is used to pump coolant at a pressure such that it generates a circumferential stress of Oyy= 20 MPa. The dimensions of the drill are given in Table .i The maximum principal stress for part AB (in MPa)ii The maximum principal stress for part BC (in MPa)iii The part of the drill (AB or BC) and location of brittle failure plane withrespect to drill bit axis.
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad