Question 3: Determine the gain value of K and the time Bepaal die winswaarde van K en die ty- constant T by using the root locus method dkonstante T deur die wortellokusmetode (by hand), such that the closed loop system (met die hand) te gebruik, sodat die geslote will have a overshoot of 4.3% and a peak lusstelsel 'n oorskiet van 4.3% en 'n piektyd time of 1.57 seconds. Check your answer van 1.57 sekondes sal hê. Kontroleer jou antwoord deur Matlab Simulink te gebruik. by using Matlab Simulink. Y(s) R(s) E(s) K(Ts+ 1) U(s) 1 s(s+2) G.(s) G(s)

Question 3: Determine the gain value of K and the time Bepaal die winswaarde van K en die ty- constant T by using the root locus method dkonstante T deur die wortellokusmetode (by hand), such that the closed loop system (met die hand) te gebruik, sodat die geslote will have a overshoot of 4.3% and a peak lusstelsel 'n oorskiet van 4.3% en 'n piektyd time of 1.57 seconds. Check your answer van 1.57 sekondes sal hê. Kontroleer jou antwoord deur Matlab Simulink te gebruik. by using Matlab Simulink. Y(s) R(s) E(s) K(Ts+ 1) U(s) 1 s(s+2) G.(s) G(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
Q2:-Find the output voltage Vo . Ry B2HF 100 kQ + 100 mV rms,
Q.6/ Modify the sawtooth generator in figure below so that its peak-to-peak output is 4V. Is it aVCO?
Determine loop current I2
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
ffasssttt plz
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
A buck converter, as shown in Figure (a) below, is working in steady state. The output voltage and the inductor current can be assumed to be ripple free. Figure (b) shows the inductor voltage Vi during a complete switching interval. Assuming all devices are ideal, the duty cycle of the buck converter is M VA 30 V- DA R TON TOFF (a) -20 V- (b)
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
A chopper circuit works at a frequency of 4 kHz of a 220 V dc supply. For 180 V output voltage, find the conduction and blocking periods of a thyristor in each cycle. Select one: a. 0.209 ms, 0.234 ms b. 0.404 ms, 0.055 ms c. 0.204 ms, 0.045 ms d. 0.704 ms, 0.897 ms
this is electric circuit questin ...plz solve it early .plz solve early