Calculate the evaporation rate from an open water source, if the net radiation is 300 W/m² and the air temperature is 30° C. Assume value of zero for sensible heat, ground heat flux, heat stored in water body and advected energy. The density of water at 30° C=996 kg/m³. [Hint: Calculate latent heat of vapourisation L by the formula: L = 2501 – 2.37 T (kJ/kg), where T= temperature in °C.]

Calculate the evaporation rate from an open water source, if the net radiation is 300 W/m² and the air temperature is 30° C. Assume value of zero for sensible heat, ground heat flux, heat stored in water body and advected energy. The density of water at 30° C=996 kg/m³. [Hint: Calculate latent heat of vapourisation L by the formula: L = 2501 – 2.37 T (kJ/kg), where T= temperature in °C.]

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.34P

See similar textbooks

Similar questions

For Cairo Egypt in January the average net radiation 40 W/m2, temperature is 14°C. relative humidity is 65%, and wind speed is 2.0 m/s measured @ a height of 2.0 m. Compute the evaporation rate by 1. Priestley-Taylor Method Zo=0.03
From an open water surface with air temperature 22°C, relative humidity is 40% and wind speed is 3 m/s, all measured at height 2 m above the water surface. Assume a roughness height of 0.03 cm. The net radiation is 200 W/m^2. Cp = 1005 J/kg-K A. Calculate the latent heat of vaporization (J/kg) B. Calculate the evaporation using Energy Balance Method (mm/day) C. Calculate the saturation deficit of the vapor pressure (Pa) D. Calculate the evaporation using Priestley-Taylor Method (mm/day)
Saturated, pure steam at a temperature of 170 °C condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 °C. Calculate: a) the local film condensation heat-transfer coefficient at the bottom of the tube.
Estimate the interfacial heat transfer coefficient for evaporation of a thin film of saturated liquid water at atmospheric pressure. The liquid film rests on a flat, solid surface to which a constant and uniform heat flux of 150 kW/m? is applied. The accommodation coefficient may be taken to be 0.05. If the liquid film thickness is 0.2 mm, compare the interfacial vaporization resistance with the conduction resistance through the liquid film.
Question 3 This question requires the use of the steam property tables (Rogers and Mayhew) uploaded on QM+ exam section. All properties should be evaluated at the temperature of the steam. Saturated, pure steam at a temperature of 170 °C condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 °C. Calculate: the local film condensation heat-transfer coefficient at the bottom of the tube. a)
Table 1 shows the physical properties of coolant at 300oC in the channel of a PWR nuclear reactor.Figure 1 shows a typical square lattice of the coolant channel within the fuel rods with rod pitch,S and rod diameter, D. From the given data and using the non-dimensional parameters such asReynolds number (Re), Prandtl number (Pr) and Nusselt number (Nu), evaluate the convectiveheat transfer coefficient, hc of the coolant during cooling
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of avertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at auniform temperature of 150 oC.Calculate:a) the local film condensation heat-transfer coefficient at the bottom of the tube. b) the average condensation heat-transfer coefficient over the entire length of the tube. c) the total condensation rate at the tube surface.
Question 3 This question requires the use of the steam property tables (Rogers and Mayhew) uploaded on QM+ exam section. All properties should be evaluated at the temperature of the steam. Saturated, pure steam at a temperature of 170 °C condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 °C. Calculate: a) the local film condensation heat-transfer coefficient at the bottom of the tube. b) the average condensation heat-transfer coefficient over the entire length of the tube. c) the total condensation rate at the tube surface.
Proflem # 27. iA fillud with water to a level and is éxposed, to dng air at 30°C. 40 mm deep a pan of of 20 mm mass diffusivity fove for time' reguired evapor ate. -3 m² /. for all the water to 2.5x 10
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat = 100°C; Properties of water at 100°C: Density, pl= 961 kg/m3; Kinematic viscosity., v 0.293x10-6 m2/s; Prandti Number, Pr = 1.740; Specific heat, Cpl = 4216 J/kg.K: Dynamic viscosity, p = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg: pv = 0.597 kg/m3; 0 = 0.0588 N/m: Csf=0.013; n=1: Select one: O a. 11633.5098 O b. 13259.1393 O c. 16641.2421 O d. 9493.7946
Classify whether the properties given is for subcooled liquid (SC), saturated liquid (SL), wet mixture (WM), saturated vapor (SV), superheated vapor (SP) or saturated (S) (can be liquid or vapor)