Curves in the below figure represent the relationship between tensile stress and tensile strain for five different materials. The "dot" on each curve indicates the yield point and the "cross" represents the rupture point. Fill in the blank spaces below with the correct number referring to a material. (5) Material has the highest elastic modulus. O a. 4 O b. 5 O c. O d. 2 O e. 1

Curves in the below figure represent the relationship between tensile stress and tensile strain for five different materials. The "dot" on each curve indicates the yield point and the "cross" represents the rupture point. Fill in the blank spaces below with the correct number referring to a material. (5) Material has the highest elastic modulus. O a. 4 O b. 5 O c. O d. 2 O e. 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. Please calculate the strain and stress in the following two prompts a. A 1 cm long section of tendon stretches to 1.011 cm when it is subjected to a tensile force of 40,000 N. What is the strain in this segment of tendon? @? 17 b. The section of the patellar ligament in the previous question is 0.02 m² in the cross section. What is the stress in this section of ligament as a result of 50,000 N tensile force? E = Δι 19 0 = A 1.011 cm 50000 0,02 Scoco 40000 1.25 = T % 2500000 strain N/m² on trito flox your wrist, you may notice that your
640 480 160 0.002 0,004 0.006 0.008 0.010 Strain (mm/mm) A tensile test specimen of Aluminum alloy having a gauge length of 280 mm was tested to fracture. Stress and strain data obtained during the test are shown in the attached Figure. **Answers are approximate - do your best to read the graph. Determine: (a) the modulus of elasticity in GPa (4sigs). Enter this value into D2L answer box. (b) the proportional limit in MPa (3sigs). (c) the ultimate strength in MPa (3sigs). (d) Ductility of material based on percent elongation. (3sigs) Your Answer: Stress (MPa)
Given the following stress-strain graph:a. is the modulus of elasticity of "A-514" greater, less or equal to the one of "A-572"?b. from the previous question, make an estimatio for both of them, check that the graphic comes in %c. If we were to test these materials in a universal tension equipment, which one would withstand more load?d. If we were to test these materials in a universal tension machine, which one would elongate the most before fracturing? would elongate the most before fracturing? e. Of the 6 materials shown, do any behave as brittle materials? f.
2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage length of 2 in. is shown in the figure below. TENSILE STRESS (MPA) 450 400 350 300 250 200 150 100 50 Part A 0 0 STRESS VS. STRAIN 0.002 0.004 STRAIN 0.006 Determine the modulus of resilience. Show units. Part B Determine the modulus of elasticity of the material. Part C Estimate the Yield Strength of the material. 0.008 0.01
stress stress MEER strain. strain stress stress strain HARD and TOUGH STRONG BRITTLE SOFT and TOUGH Q/Interpret the following drawing strain
You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear modulus for your calculations? 200 GPa O 60 GPa O 77 GPa O 154 GPa
1. A tensile test was conducted on a metal "505" specimen and the following stress-strain curves were generated, both curves generated from the same set of data. Use the graphs to fill in the mechanical properties of the material tested in the box below. Don't forget units! Stress vs Strain Stress, psi Stress, psi 80000 70000 60000 50000 40000 30000 20000 10000 0 0.00 80000 70000 60000 50000 40000 30000 20000 10000 0.02 0 0.000 0.002 0.04 0.004 0.06 0.006 0.08 0.10 Strain Stress vs Strain 0.008 0.12 Elastic Modulus, E: 0.2% Offset Yield Strength, oo: Tensile Strength, ou: Breaking Strength, of: % Elongation: 0.14 0.010 0.012 0.014 Strain 0.16 0.18 0.016 0.018 0.20 0.020
Please answer these three questions. Thank you! A material has a Poisson’s ratio of -0.2 . Which of the following is true? a. Strain is always compressive regardless of the force applied. b. Lateral and longitudinal strains will have the same sign c. Lateral strain is five times the longitudinal strain. d. The material is ductile and has a high modulus of elasticity. Consider a rod that can carry a maximum stress equal to 200 MPa. If it is to be designed to have a factor of safety against failure equal to 1.5, then the maximum stress that the rod should experience when loaded is nearest to ______ a. 133 MPa b. 150 MPa c. 300 MPa d. 267 MPa Which of the following statements is FALSE? A. The modulus of elasticity of a material can vary between axes. B. The modulus of rigidity can be determined from the shear stress-strain diagram. C. The Poisson’s Ratio can be used in calculating the new diameter in the Necking Region of the stress strain diagram. D. Most materials…
b) A 1.25 m long cable has a diameter 3.50 mm with a Young's Modulus, E, of 9.75 x 10⁹ N/m². When the wire is placed under tension, it experiences a stress of 202.52 x 106 N/m², the length of the cable extends by 36.35 mm. Calculate the force that the cable experiences under tension and the strain energy density (U/V) due to deformation. Give your answers in newtons (N) to 2 decimal places for the force; and in joules per cubic metre (J/m³) for the strain energy density to 2 decimal places. Assume the cable is solid and the material is homogeneous. c) Figure Q1c shows a bracket on rollers that allow the bracket to move along a beam in the horizontal direction. A force F₁ of 2625 N acts at point A where the angle between F, and the x-axis is 100. If force F₂ acts at an angle a = 400 between F2 and the y-axis: (i) Determine the magnitude of F2 necessary to maintain bracket on horizontal equilibrium. (ii) Determine the vertical force at A acting along the y-axis. Give your answers to the…
Help me please
1. The table shows the results of a tensile test with a sample with a cross-sectional area of 100 mm2 and an initial length of 100.000 mm. (1) Plot the data as engineering stress versus engineering strain. Use the standard unit [Pa] or [MPa]. (2) Determine the modulus of elasticity and the yield strength at a strain offset of 0.002. Load (N) Length (mm) 100.000 40000 100,200 80000 100.400 120000 100,600 140000 100.800 160000 101.000 180000 101.400
, A material is subjected to two mutually perpendicular linear strains together with a shear strain. Given that this system produces principal strains of 0.0001 compressive and 0.0003 tensile and that one of the linear strains is 0.00025 tensile, determine the magnitudes of the other linear strain and the shear strain. [- 50 x 10-6, 265 x 10-6.]