Design a combinational circuit using multiplexer for a car chime based on the following system: A car chime or bell will sound if the output of the logic circuit (X) is set to a logic '1'. The chime is to be sounded for either of the following conditions: • if the headlights are left on when the engine is turned off and • if the engine is off and the key is in the ignition when the door is opened. Use the following input names and nomenclature in the design process: • 'E' - Engine. '1' if the engine is ON and '0' if the engine is OFF 'L' - Lights. '1' if the lights are ON and '0' if the lights are OFF • 'K' - Key. 1' if the key is in the ignition and '0' if the key is not in the ignition • 'D' - Door. '1' the door is open and '0' if the door is closed • 'X' - Output to Chime. '1' is chime is ON and '0' if chime is OFF

Design a combinational circuit using multiplexer for a car chime based on the following system: A car chime or bell will sound if the output of the logic circuit (X) is set to a logic '1'. The chime is to be sounded for either of the following conditions: • if the headlights are left on when the engine is turned off and • if the engine is off and the key is in the ignition when the door is opened. Use the following input names and nomenclature in the design process: • 'E' - Engine. '1' if the engine is ON and '0' if the engine is OFF 'L' - Lights. '1' if the lights are ON and '0' if the lights are OFF • 'K' - Key. 1' if the key is in the ignition and '0' if the key is not in the ignition • 'D' - Door. '1' the door is open and '0' if the door is closed • 'X' - Output to Chime. '1' is chime is ON and '0' if chime is OFF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
16. What is the two's complement of 1011100111? 17. Explain function of each element in Figure 3. (Register A, B, C, Clock, Carry out,D, C, Q, PRE, S, CI, CO) Subtractor Circuit Register A Register C Register B PRE Carry Out (Sign Bit) CI CO Clock- Figure 3 18. In the Figure 4, Register A is 1011 and Register B is 0010. a. What are the contents of register C after 2 clock pulses? b. What is the output of flip flop (Q) after the second clock pulse? c. What is the output of flip flop (Q) after the third clock pulse? d. What are the contents of register C after 5 clock pulses? Adder Circuit Register A Register C Register B B CLR CI CO Q Clock Figure 4 19. The serial adder required ten clock pulses to add two, five bit binary numbers. (True or false. İf it is false write correct one .) 8.
3) Here is a Digital Logic question on analysis of clocked sequential circuits with the answer. Please explain what the teacher did and why they did it. I need you to explain how they got the answer.
It's a Digital Electronics/Digital Logic question.
3) Here is a Digital Logic question on registers and counters with the answer. Please explain what the teacher did and why they did it. I need you to explain how they got the answer.
Choose the false statement. a. In SCR the gate is the controlling terminal b. SCR are used for high-power applications c. SCR is a controlled device d. SCR is a bidirectional device
Logic circuit Multiplexer In this question I used same question for two different cell scheme types First one I used up to down cell scheme like 0 4. 12 8 1. 5. 13. 9 3. 7. 15. 11 2 8. 14. 10 Function is €m(0,5,6,8,9,10,14) I got in the letter below I0=B’ Means B complement I1=A’B+AB’ I2=A+B I3= 0 But second k map cell scheme I used like this right to left for the same function 0. 1. 3. 2 4. 5. 7. 6 12. 13. 15. 14 8. 9. 11. 10 But I got different answers for the same function I0=A’B’. I1=A’B+AB’ I2=AB’. I3 = A’+B’ Only i1 I got the same but isn’t which ever cell scheme you use the answer shouldn’t be different right or I do it wrong please look the picture carefully give brief explanation where did I understand wrong
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? What is the error type that happened in that reading? b) c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we d) minimize it?
12)Coils labeled ( S ) and ( R ) A)may be used only in subroutines in programs for Siemens PLCs B)may be used instead of a seal-in arrangement to provide latching C)must appear in that order (S before R) in a ladder logic program D)are Short and Repeated coils, used in timing programs
What is the intermediate calculation process？
Question No.3: Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “5410” should display on 7-seg Display and when user press 2 leds should glow 5 times in a loop. If any other key is pressed no action should be taken