Find the amplitude, phase, period, and frequency of the sinusoid: i(t) = 100 sin(100πt +110°) == Quantity The period T (2 decimal point) The frequency F (2 decimal point) The peak value The peak to peak value The average value. The rms value. (2 decimal point) The phase The instantaneous value at 1.01 s (2 decimal point) Value Unit ms Hz A A A A Deg A 4 (

Find the amplitude, phase, period, and frequency of the sinusoid: i(t) = 100 sin(100πt +110°) == Quantity The period T (2 decimal point) The frequency F (2 decimal point) The peak value The peak to peak value The average value. The rms value. (2 decimal point) The phase The instantaneous value at 1.01 s (2 decimal point) Value Unit ms Hz A A A A Deg A 4 (

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

▲e 10 V- 0 ₂ Sine wave A In the plot of Sine wave A shown above, the value of t₁ is 15.0 ms. Enter the appropriate values for terms in the table below: Period of the waveform (T) Frequency of the waveform (f) Angular frequency of the waveform (w) Peak-to-peak voltage (Vpp) RMS Voltage (Vrms) Time tab Phase angle of waveform (4) Time t2 if the voltage is 6.00 V at time t2 5.00 200. 20.0 t1₁ *Units are provided, be sure to use proper three significant digits for all answers. ms Hz rad/s V V ms ms
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequency of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms - (iii) Determine phase relationship between voltage and current waveform. (c) From the measurement process, the circuit generated two different outputs, V,(t) and V,(t) with the same peak voltage. The V,(t) lagging V,(t) by 100°. If V,(t) =150sin(1000t – 40°)V , determine the RMS value and phase angle of.
Q2. For the Periodic Waveforms shown in the Figure, determine for each : Frequency, Average Value over half a cycle, RMS Value, Form Factor, and Peak Factor. 100 75 Voltage (V 50 25 20 40 Time (ms) 10 30 -100
When measured by an analog meter, a sinusoidal voltage shows a reading of 100 Vrms. What is the amplitude of the voltage source? A 140 V B) 141 V c) 142 V D 143 V
1. A Sinusoidal current has an rms value of 5mA. Determine the following values. 1) Peak 2) Average 3) Peak to Peak
Calculate the rms value of a sinusoidal current of maximum value 20A.
An alternating current varying sinusoidally with a frequency of 50Hz has an RMS value of 20A. a. Write down the equation for the instantaneous value b. find the value of (i) at 0.0025 second
iii) A sine waveform with following specifications. RMS voltage 161.4V Time for ten cycles 0.02s Sketch the waveform.
What is the ripple factor of a sinusoidal signal having an rms of 56 V on an average of 50 V? r-Blank 1 V at least 2 decimal place Blank 1 Add your answer
An alternating current varying sinusoidally with a frequency of 50 Hz has an rms value of 40 A. Find: a. The instantaneous value of 0.0025 seconds after passing through maximum positive value, b. The time measured from the maximum value when the instantaneous current is 14.14 A.
An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive phase of 30°. While the RMS value of current is 66.71 A with negative phase of 0.349 rad. Assume the frequency of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Find the time, t in the first cycle when current is – 80A (iv) Determine phase relationship between voltage and current waveform.