From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an outer d = 0.2m and thickness of 10 mm. Bar (b) is also a hollow bar with outer d = 0.15 m with same thickness as bar (a). If T1= 42,000 N-m and T2 = 18,000 N-m, Find the max shear stress in bar (b). Answer in MPa.

From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an outer d = 0.2m and thickness of 10 mm. Bar (b) is also a hollow bar with outer d = 0.15 m with same thickness as bar (a). If T1= 42,000 N-m and T2 = 18,000 N-m, Find the max shear stress in bar (b). Answer in MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
P (1) B A A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are circular section diameters of 50 mm and 25 mm, respectively. If the normal stress in (1) is 40 MPa. Determine the following: The area of Segment (1) is equal to in mm?: The area of Segment (2) is equal to in mm²: The axial force (P) is equal to in kPa: The Normal Stress in Segment (2) is equal to in MPa:
A solid section di = 50 mm diameter steel bar; It is placed in a steel tube with an inside diameter d2 = 65 mm and an outside diameter d3 = 75 mm. The rod and tube are rigidly supported at point A and rigidly connected to a cover plate at point B. L = 660mm, T = 2 kN.m a) According to the maximum shear stress in the rod and tube; b) Calculate the angle of rotation of end B in degrees. (G = 80 GPa)
Q1. A crane hook has a triangular section at x-x as shown in Fig. Find the maximum stress at point P. 5 kN 60 0: 40 20 An dimiencions in mm
A flat bar is 3/8 inches thick and has a centrally located drilled hole of diameter D. The bar is subjected to a 4,000 lb tensile load. Compute the maximum tensile stress adjacent to the hole. a) If the bar is 2 inches wide and D=0.25 inches b) If the bar is 2.5 inches wide and D=0.5 inches c) If the bar is 3 inches wide and D=1.00 inches Answers: a) = 15,969.5 psi (using k=2.62) b) = 13,066.7 psi (using k=2.45) c) = 12,000 psi (using k=2.25) I have no idea how to come up with these answers. Could you help me go through the process of solving for these answers step by step?
AB brass and BC from aluminum bar ABC in shape composite rod was obtained. Composite rod B 0.05 mm opening at the point, the elongation of the rod There is a rigid obstacle preventing it. Composite rod 30 when pulled with kN; a) the displacement of point C, b) Find the stresses in bars AB and BC. (Ep = 105 GPa, Eal = 70 GPa) dimensions in mm
Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using the free body diagram concept illustrated in Fig. below, 1. Show that the shearing stress on a plane inclined at any angle 0 to a transverse section of area A is T=Psin20/2A? Given: sin 20 = 2 sin 0 cos 0. 2. Determine the shear stress, if the axial load P = 6000 N.? funu ost P
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
2 3.0 m 175 KN 2.5 m 200 KN (1) (2) 46 mm 175 kN 30 mm Problem 3 A compound axial member consists of steel (E=200 GPa) segment (1) and brass (E=120 GPa) segment (2). a) Compute the total deformation of the compound member for the loading shown (in mm). b) Sketch an internal normal force diagram c) Calculate the average axial stress in segment 2