Answered: " gusset PL PL 76 x 2½ A36 steel…

Engineering

Civil Engineering

" gusset PL PL 76 x 2½ A36 steel 4"-diam. bolts 1.5" 3" 1.5"

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.8.3P

See similar textbooks

Related questions

Q: O O Lin Figure -1 10in For the Section shown in the Figure-1 above, Compute connection capacity for…

A: A bolt is generally a metal pin with a head at one end and the ends are a shank threaded and receive…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: LRFD It applies Ultimate factored loads to design. Evaluate forces and stress using yielded…

Q: 3-25. A36 steel and 3/4-in Ø bolts (Ans. LRFD 170.42 k, ASD 113.39 k) - L7 x 4 x} 1 in 3 in 2 in 3…

Q: 9. The limit states A. tensile and shear ruptures B. pin bearing 10. The spacing between bolts in…

A: According to AISC part 16.1 , the spacing between bolts in painted built up tension member is 7-in…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Given: Diameter of bolt= 1 inch ( Group A ) Diameter of bolt hole= d0 =116+1=1.06 inch Plate…

Q: In the figure shown, the bolts are 3/4-inch in diameter, and A36 steel is used for all components.…

A: Introduction- Overall shearing capacity of a bolt is the amount of force required to split the bolts…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: For the connection shown in the accompanying illustration, Pu = 475 k and Pa = 320 k, determine the…

A: LRFD: Load and Resistance Factor Design is used for designing steel structures and structural…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

Q: Compute the net area. The 1 x 10 plate shown in Fig. P3-10.The holes are for 7/8-in Ø bolts.

A: The calculation of the net area An of the plate is given by - An = Bt - nϕht + nss24ghere,B =…

Q: CLO3: Determine the tensile capacity of the 1/2-in. by 7-in. plate shown in Figure bellow. The…

A: Given: The cross-section of the plate is ½ in x 7 in. The diameter of the bolt is 6/8 in. The value…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Weld Capacity : Weld capacity of a shear connection is determined by calculating the shear strength…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Design strength for tension on gross area=∅Rn For LRFD, ∅Rn=0.75Rn Tension on gross area=Rn=Fy×Ag…

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: ngth of sections shown in the figure. A36 steel and 4-in Ø bolts. -L6x 3를 x 를 2} in 3 in -le le

A: According to given data Determine the LRFD design strength and the ASD allowable strength of…

Q: 4-2. Determine the following for the connection shown in Figure 4-26, assuming the bolts are -in.…

A: Bolted Connection: A small piece of metal that consists of a head and a shank is known as a Bolt.…

Q: a. The plate in Figure 1 if a 22-mm bolt is used in a staggered connection shown. The plate. is…

Q: a) Design shear capacity of beam web against tearing is b)Calculate and verify the design shear…

Q: A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572…

A: Tensile capacity, the maximum load that a material can support without damage when being determined…

Q: Determine the critical net width for the staggered bolted connection as shown in the figure. The…

Q: Determine the critical net width for the staggered bolted connection as shown in the figure below.…

A: We will use formula of net width along section A B C D E .

Q: Example 5.13 The connection shown in Fig. Ex. 5.13 uses 20 mm diameter 10.9S grade bolts with…

A: Given that :

Q: Question No.3: Determine the maximum tensile force, Pu, that can be applied to the connection shown…

A: Given:- ASTM A36 steel From AISC Manual Table 2-4, fy=36ksi fu=58ksi To find:-Pu

Q: Determine the avaiable 2" streugth of 34" 3" 2 A325 -N bolts in 1.25 3" 3" 1.25" the lap splice with

A: The given data is: A 325-N bolts-with 3/4 diameter. The dimensions of the section is shown in…

Q: Determine the design strength of the connection shown in the Figure below. The bolts are 25 mm…

A: Given Data Diameter of bolt is given as 25 mm Ultimate tensile strength is given as 400 MPa Yield…

Q: The details for a riveted connection are given in the figure below. The angle steel section is…

A: Data Given: Section L 100 × 75 × 9 P = 8.5 t Asked: Net area required for the checks on the…

Q: A bolfed lap joint is shown below. The bolts used are A325, Grade 2, hof-driven vith diameter of…

A: Failure of bolted joints takes place in three ways- 1. Shearing failure of bolts. 2.Bearing failure…

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: In the connection shown in Figure P3.5-3, the bolts are 4-inch in diameter, and A36 steel is used…

A: Given,

Q: 4-22 mm diameter bolts are used in a staggered bolted connection as shown in the figure. Calculate…

Q: The small postal scale consists of a counterweight W1, connected to the members having negligible…

A: The given figure is shown below:

Q: 20 find the required fillet welds size if the alloweble shearstress is (9.4kN/km²) forthe figure…

A: C.G of the weld on X axis x=190×95+190×95+250×0190+190+250=57.3 mmand on y axis y=2502=125…

Q: Determine the ASD or LRFD weld size in the connection shown P = 16 kips 15" 9" 6" E70

A: Steel design or structural steel design there are two methods taking into account. The first one is…

Q: igure Q1(b) shows a glued connection between 3 metal plates. The plate ide. The glue has a shear…

A: Concept- each glue will take a force of P/2 Kn Bolt will have 2 shear planes

Q: In the connection shown in the figure, the bolts are 3/4 inch in diameter, and A50 steel is used for…

Q: Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown…

A: Solution: Given: Section: 2 L5x3x1/4 LLB d = 5 in = 127 mm bw = 3 in = 76.2 t = 1/4 in = 6.35 mm…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: %" Dia bolts in standard holes. W8 FIGURE 2 134 3@3.00

Q: Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm…

Q: A gusset plate is bolted to a larger plate by for 22-mm-diameter bolts arrange as shown, separated…

A: The given data is: Diameter of bolt=22 mm r1=r4=80+40=120 mm r2=r3=80+40=120 mm n=4

Q: A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are…

A: Given, For Steel grade S355JR, fy=350 MPafu=490 MPa For bolts of 8.8 grade, fub =800 N/mm2 Assuming…

Q: A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: While ASD uses a constant factor of safety for all designs, regardless of the load type, LRFD means…

Q: Which of the following gives the minimum number bolts that can be accommodated in one row of a 350mm…

Q: 3-11. The 7/8 x 14 plate shown in Fig. P3-11. The holes are for 7/8-in Ø bolts. (Ans. 10.54 in?) |3…

A: Calculate the net area along each possible path from one end to other end of plate. The least one…

Q: Determine the design strength for the bearing type connection shown in the figure below. The bolts…

A: Solution

Q: 1. In the butt joint shown below, the 7/8-inch diameter boits are made of A325 steel with threads…

A: Area of bolt=π4d2=π4(78)2 A=0.601 in2a)The allowable stress for the bolt is SS=24 Ksi (from table of…

Q: Q3) Determine the total number of 4-inch, A325 bolts required for the tension splice in Figure. The…

A: The given figure is shown below:

Q: Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection…

A: The given data is shown below: Bolt diameter=78''A36 steelWidth pf plate=13''

Q: Compute the net area. The plate 7/8 x 14 shown in Fig. P3-11. The holes are for 7/8-in Ø bolts.

A: Diameter of the bolt,d= 7/8inch Assuming, clearance, c=1/16inch Diameter of the hole,do=7/8…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Determine the strength of the connection shown in Figure , based on bearing and shear, for the following bolts:

a. A307 b. Group A, threads in the plane of shear c. Group A, threads not in the plane of shear

" gusset PL
PL 76 x 2½
A36 steel
4"-diam. bolts
1.5"
3"
1.5"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3 10" 2" EI 4" -2" 2" 12" UT 8' A992 steel. &Mp= ?
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
10 – 7/8" Bolts Gusset Plate Plate thickness t = ½" 2" b. 2" Tension Member A36 Steel Plate 2" P 12" 2" g I 2" Calculate Tension Capacity 2" of line 1. abcde (A,„) 2. abfcgde (A„) 3. abfgde (A,), and 4. Yielding over Agross An A 3" 3"
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
2 hEe c W@ B & - For the beam shown find the value of Force (F) Ib and maximum stress due to flexure ( oy ) psi if the shear force in bolts is 300Ib and the shear stress in beam 120psi. Spacing between bolts (S) =5in F T —————————————+% 4ft 8ft 1in 1in -~ - 10in 1n § 8in
Compute the tensile capacity for the ½ inch thick plate shown. The bolts are ¾ inch diameter high strength bolts. The steel is A36. 24" -P, 1 3"
Situation 7 Refer to FIGURE-1. For shear and moment calculations, use the NSCP Coefficients Section 408-4 provided in the problem. File Home Insert Draw Design Layout References 2 Share % Cut FIGURE-1 Calibri (Body) 11 A A Aa - Given: L1 = L2 = 6m e Copy Paste BIU - abe X2 x A v aly - L3 = 7.0 A. B V Format Painter S = 2.5 m Column Section (all columns), bxh = 350 mm x 450 mm Slab Thickness, t = 100mm Clipboard Font Concrete, f'c = 27.5 MPa Steel Bar, fy = 415 MPa Loads: Dead Load, W, = 5.0 Kpa M L1 L2 L3 Live Load, W = 3.6 Kpa 18. What is the moment (KNm) at midspan of beam FG. а. 67 b. 58.6 c. 85.3 d. 117.3 19. What is the moment (KNm) at end F of the beam EF? а. 144.1 b. 93.80 c. 105.8 d. 117.6 20. What is the shear (KN) at end F of beam EF? а. 78.0 b. 85.21 c. 95.50 d. 99.20 21. Determine the maximum moment (KNm). а. 93.80 b. 111.20 с. 118.2 d. 130.01 22. Find the value of the maximum shear (KN). a. 112.4 b. 95.50 c. 83.04 d. 93.80 23. Determine the maximum reaction (KN). a. 95.50…
The 200 mm x 150 mm x 12/5 mm angle has one line of 20 mm diameter bolts in each leg. The bolts are 75 mm on center in each line and are staggered 37.5mm with respect to each other. Fy 248 MPa, Fu-400 MPa. Standard nominal hole diameter of 20 mm bolt is 21mm. Area of the angular section= 4355 mm2. Reduction coefficient U-0.75 CIVIL ENGINEERING STEEL DESIGN Compute The following: a) The effective net area b.)The design strength for LRFD. c) The allowable strength for ASD. 200 75 (1125 67.5 150 1125 1125
ج اس. ا. ۲۳% ۳:۷ 385.2 kips 6 نقاط The available tensile strength of plates shown below is .( use A 36 steel * material) 1/4" "I1/4می T1/4" 6" 1½". 3" 1½" O 3/4" bolt 51.32 kip 40.51 kip 46.24 kip 53.53 kip صفحة 3 من 3 إرسال رجوع عدم إرسال كلمات المرور عبر نماذج Go ogle مطلقا. لم يتم إنشاء هذا المحتوى ولا اعتماده من قبل Google. الإبلاغ عن إساءة الاستخدام - شروط الخدمة ۔ ہسياسة الخصوصية
Bolted and Riveted Connections From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm bigger than the bolt, the angular section is 100 x 75 x 8 mm, with an area of 1340 mm2. Thickness of the gusset plate is 9mm. The gusset plate and angle arc A36 steel with Fy = 250 MPa and Fu = 400 MPa. Determine the tensile capacity of the connection based on gross area. Determine the tensile capacity of the connection based on effective net area using a reduction factor of 0.85. Determine the tensile capacity of the connection based on gross area.