4-22 mm diameter bolts are used in a staggered bolted connection as shown in the figure. Calculate the value of "x" such that the net width in chain A-B-C-D is equal to the net width of the chain A-B-D. 35mm 1Smn S0nun 200mm 70mm 40mm TTT

4-22 mm diameter bolts are used in a staggered bolted connection as shown in the figure. Calculate the value of "x" such that the net width in chain A-B-C-D is equal to the net width of the chain A-B-D. 35mm 1Smn S0nun 200mm 70mm 40mm TTT

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Related questions

Q: Q21 In the connection shown in Figure below, the bolts are ¾in diameter, and A36 steel is used for…

A: The figure shown below shows the A36 steel connection with 1" bolts

Q: A bracket cut from a W310X179 is connected to a W310X179 column flange with 12 A325 bearing-type…

A: Brackets are the projections which carry loads. The bracket which is connected to a support must…

Q: Angle Bolted Connection. The L6 x 31/2 × 5/16. -in angles, shown in Figure, The bolts are 3/4 inch…

Q: 1. A riveted lap joint is shown in the figure below. The rivets used are A502, Grade 2, hot-driven…

Q: A plate with width of 500 millimeters and thickness of 25 millimeters is to be connected to a double…

Q: 10/.. find the shear stress in bolts (4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM…

A: Given, P = 80kN Diameter of bolt = 10mm No. Of bolts = 8, Shear stress on the bolt=…

Q: The bolted connection shown in Figures is connected with 3/4-in-diameter bolts in standard holes.…

A: To find = Available tensile strength of plates

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Weld Capacity : Weld capacity of a shear connection is determined by calculating the shear strength…

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: a. The plate in Figure 1 if a 22-mm bolt is used in a staggered connection shown. The plate. is…

Q: Determine the critical net width for the staggered bolted connection as shown in the figure. The…

Q: Bolted and Riveted Connections 1. From the bolted connection shown, the diameter of bolts is 18mm0…

A: Solution: Given: db = 18 mm dbo = 18+3 = 21 mm Section: 100 x 75 x 8 mm Ag = 1340 mm2 t = 9 mm A36…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: Consider the free body diagram;

Q: D=95k O O o O L = 9k PL ½x 8

A: Calculate gross area and net area:

Q: Question No.3: Determine the maximum tensile force, Pu, that can be applied to the connection shown…

A: Given:- ASTM A36 steel From AISC Manual Table 2-4, fy=36ksi fu=58ksi To find:-Pu

Q: Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square…

Q: j) what is the bolt shear capacity of the flange connection in kips? (2 decimal places) A992:…

A: Answer We are given W 16 x 50 beam Flange A 992 (fy = 50 ksi , fu = 65 ksi) Effective bolt hole…

Q: Determine the design strength of the connection shown in the Figure below. The bolts are 25 mm…

A: Given Data Diameter of bolt is given as 25 mm Ultimate tensile strength is given as 400 MPa Yield…

Q: Calculate and check the design strength of the connection shown below. Is the connection adequate…

Q: The details for a riveted connection are given in the figure below. The angle steel section is…

A: Data Given: Section L 100 × 75 × 9 P = 8.5 t Asked: Net area required for the checks on the…

Q: If the nominal diameter of a bolt in a bolted connection is 7/8 in, then the minimum distance…

A: A bolt is a mechanical object that is used for fastening with the threaded shaft. They are similar…

Q: A bolfed lap joint is shown below. The bolts used are A325, Grade 2, hof-driven vith diameter of…

A: Failure of bolted joints takes place in three ways- 1. Shearing failure of bolts. 2.Bearing failure…

Q: From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Yield Strength : Yield strength is a maximum stress a structure can bear beyond the maximum stress…

Q: A bracket connection is made with four bolts of 10 mm diameter and supports a load of 10 kN at an…

A: Given:- The diameter of the bolts connected to the bracket connection = 10 mm The number of bolts =…

Q: In the connection shown in Figure P3.5-3, the bolts are 4-inch in diameter, and A36 steel is used…

A: Given,

Q: Determine the strength of the connection shown in Figure , based on bearing and shear, for the…

A: For both holes, calculating the bearing deformation strength:Rn=2.4dtFu =2.4(3/4)(3/8)(58) =39.15…

Q: In the connection shown in the figure, the bolts are 3/4 inch in diameter, and A50 steel is used for…

A: The given data is shown below: Diameter of bolt=34-inchA50 steel

Q: Calculate the number of bolts required at the end connections of the angle to the gussets using 20…

Q: 2. Determine the net area of a W12X16 given a staggered bolt connection in the web in in?. Assume…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi,…

A: Tensile Strength: The Tensile strength of a material defines as the stress in tension that the…

Q: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The…

Q: 1. In the butt joint shown below, the 7/8-inch diameter bolts are made of A325 steel with threads…

A: The width of the plate is B=12 in. The thickness of the plate is t=58 in. The diameter of the bolt…

Q: Problem 1. Given the bolted connection as shown and using 25 mm diameter bolt, determine shear…

A: Shear force due to direct shear:F1x=0, F1y=15010kN=15kN

Q: Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm…

Q: A bracket plate is welded to the flange of a column section I.S.H.B. 300 @ 618 N/m, as shown in Fig.…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Block Shear Rupture : The block shear failure causes due to high shear strength bolts or the use of…

Q: What will be minimum number of bolts required in each row for a suitable bolted bracket connection…

A: Given data,

Q: 6) The connection shown in the figure uses 20mm diameter A325 bolts. The tension member is A36 steel…

Q: 1- A double angle section with unequal legs (200x100×12), long legs back to back is connected to a…

Q: The bolted connection shown in Figures is connected with 3/4-in-diameter bolts in standard holes.…

A: To find Available tensile strength of plates

Q: Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm…

Q: A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is…

A: Given:- W 16 x 40 To find:- a) nominal strength based on gross area b)nominal strength based on…

Q: Determine the design strength for the bearing type connection shown in the figure below. The bolts…

A: Solution

Q: 4-22 mm diameter bolts are used in a staggered bolted connection as shown in the figure. Calculate…

A: Schematic diagram of the given problem: Width of the plate (B) = 200mm diameter of bolt holes (d) =…

Q: A staggered connection is shown in the figure. Using LRFD & ASD, determine the maximum tensile force…

Q: T 11 175 k 175 k The bolted connection shown is to be used to transmit a tension of 175 kips by…

Q: 60 mm b Bottom Plate f100 mm Top Plate Ț100 mm t100 mm 150 A Plate with width of 400 millimeters and…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Yield Strength : Yield strength is a maximum stress a structure can bear beyond the maximum stress…

Q: 8. The specialty wrench shown is used for difficult-to-access bolts which have a low torque…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

From the preceding problem, determine the ultimate tensile force P. that the bolted connection could carry against tensile rupture in the net section. Use A- 50 steel and LRFD.

4-22 mm diameter bolts are used in a staggered bolted connection as shown in
the figure. Calculate the value of "x" such that the net width in chain A-B-C-D
is equal to the net width of the chain A-B-D.
35mum
15mm
50mm
Pa
200mm
70mm
40mm
TTT

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
The diagonal at the left to the connection is a double angle 90 mm x 90 mm x 8 mm, with area of 2700 mm?, bolted to the 8 mm thick gusset plate. Bolt diameter = 16 mm Bolt hole diameter = 18 mm Bolt bearing capacity, Fp = 480 MPa Bolt shear strength, Fv = 68 MPa Steel plate strength and stresses are as follows: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 0.60 Fy Allowable tensile stress on the net area = %3D 0.50 Fu Allowable shear stress on the net area = 0.30 Fu Bolt bearing capacity, Fp = 1.2 Fy Calculate the allowable tensile load, P(kN) under the following conditions: %3D
Determine the critical net width for the staggered bolted connection as shown in the figure below. The diameter of the bolts is 19 mm. Use depth 4y = 200 mm. %3D x = 0.8y A y y E.
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
4-22 mm diameter bolts are used in a staggered bolted connection as shown in the figure. Calculate the value of "x" such that the net width in chain A-B-C-D is equal to the net width of the chain A-B-D.
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
The bolted connection shown in Figures is connected with 3/4-in-diameter bolts in standard holes. The plate material is A36 steel. By using strength level design (LRFD), find the available tensile strength of the plates. u=0.8 (5)-¾" bolts 4" C12× 20.7 | 4½" ,3" , 4½" |
Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm while holes have 21 mm diameter. Use depth 4y = 200 mm. 1. Determine the critical net width (Net Width) for the staggered bolted connection as shown in the figure. 2. Determine the value of "x" so that the net width along bolts A-B-C-D-E is equal to the net width along bolts A-B-D-E.
In the figure shown, the bolts are 3/4-inch in diameter, and A36 steel is used for all components. Considering both the tension member and the gusset plate, compute the following: Note: Limit the failure path to U-shape 3 a. Design block shear strength of the connection 2" b. Allowable block shear strength of the connection
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips