In a Reheat Cycle steam enters the turbine @ 40 bar and 400 C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400 C. This steam expanded isentropic ally to 1 bar and is reheated at constant pressure to 200 C. Finally this steam is expanded isentropic ally in the condenser pressure of 0.1 bar. Determine the thermal efficiency and the capacity of the boiler if 10,000 KW of power output is required.

In a Reheat Cycle steam enters the turbine @ 40 bar and 400 C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400 C. This steam expanded isentropic ally to 1 bar and is reheated at constant pressure to 200 C. Finally this steam is expanded isentropic ally in the condenser pressure of 0.1 bar. Determine the thermal efficiency and the capacity of the boiler if 10,000 KW of power output is required.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 13RQ: Condensers in these refrigerators are all_______cooled.

See similar textbooks

Similar questions

In a reheat cycle steam at 15 MPa, 540 degrees Celsius enters the engine and expands to 1.95 MPa. At this point the steam is withdrawn and passes through a reheater. It reenters the engine at 540 degrees Celsius. Expansions now occur to the condenser pressure of 0.0035 MPa. Find the efficiency.
3- A reaction turbine is supplied with steam at (60 bar, 600 C°). The condenser pressure is (0.07 bar). If the reheat factor can be assumed to be (1.04) and the stage efficiency is constant throughout at (80%). Calculate the steam flow required in (ton/hr) for a diagram power of (25 MW). (Ans. 75.6 ton/hr) 4- The steam consumption at full load for a (3 MW) turbine is (16.6 ton/hr). At half load the steam consumption is (9.1 ton/hr). Applying Willan's line, estimate the steam consumption at no load, and the consumption at a load of (2.5 MW). (Ans. 1.6 ton/hr; 14.1 ton/hr)
In a Reheat Cycle, steam at 2,350 psia and 1,100°F enters the engine and expands to 260 psia at this point the steam is withdrawn and passed through a reheater. It re-enters the engine at 900°F. Expansion now occurs to the condenser pressure of 0.5 psia. For an ideal cycle, find the thermal efficiency.
1. Steam is supplied to a two-stage turbine at 140 bar and 400C. It expands isentropic ally until it is just dry-saturated. Then it is reheated to 350C at constant pressure and expanded in the second-stage turbine to the condenser pressure of 0.2 bar. If the isentropic efficiency of the second stage is 78%. Calculate the specific steam consumption and the thermal efficiency. Determine the pressure in reheater also to solve the whole problem
When a steam boiler generates saturated steam at 2.5 mpa and the condenser pressure is 20 kpa, what is the Rankine cycle efficiency?Show complete step-by-step process and solution.
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 5. Calculate the thermal efficiency of the cycle
A turbine is supplied with steam at 25 BAR, 42C and exhaust into a condenser at 55 KPa. Find the thermal efficiency of the cycle. Draw the schematic and T-S diagrams with corresponding labels. (Clear handwritten and step by step solution)
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 + (200/13) kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: PV and TS diagrams of the cycle showing ideal and actual process lines Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Rankine engine efficiency (%). Ans.____________________________ Cycle thermal efficiency ( %). Ans.____________________________
2. In a reheat cycle steam enters the high pressure turbine at 40 bar and 400°C. It expands isentropic ally to 6 bar and is reheated at constant pressure to 400°C. This steam is expanded isentropic ally in the low pressure turbine to the condenser pressure of 0.1 bar. Calculate the thermal efficiency and steam consumption for 10 MW output.
A medium size power station is used to produce 30 MW net power for arefinery. The station uses steam as the operating fluid and operatesaccording to the Carnot cycle between the pressure limits of 0.4 bar and35 bar. Steam enters the boiler as a saturated liquid and leaves it as adry saturated vapour. (i) Calculate the thermal efficiency of the power station if theisentropic efficiency of the steam turbine is 94%. (ii) State main disadvantages of using the Carnot cycle as the basis fora power station. (iii) State the name of the cycle that is used in practice in powerstations, along with three key benefits over the Carnot cycle.
3. Operate at lower condenser of a Rankine Engine. P1=50 bar (saturated) P2=½bar=0.5 bar. Calculate the efficiency of cycle and engine using Mollier chart. Can you show step by steps solution using the formula given?
1. Figure shows a reheat cycle in which steam is delivered to the high-pressure turbine at 1100 Ibf/in^2, 740 F, and expanded to 200 Ibf/in^2. After the expansion, the steam is warmed to 720 F before being expanded to 1 lbf/in^2 in the low- pressure turbine. Assume the turbines and pump are adiabatic. Compute the high pressure isentropic turbine work. High Q'în Boi ler Condenser Pump Q out 166.8 Btu/lbm 200.1 Btu/lbm 190.2 Btu/lbm 231.1 Btu/lbm 120.5 Btu/lbm