In the figure, rigid tee-beam ABC is supported at A by a single shear pin connection and at B by a strut, which consists of two 27-mm-wide by 5-mm-thick steel bars. The pins at A, B, and D are each 11 mm in diameter. The yield strength of the steel bars in strut (1) is 291 MPa, and the ultimate shear strength of each pin is 578 MPa. Determine the allowable load P that may be applied to the rigid bar at C if an overall factor of safety of 2.2 is required. Use L₁ = 0.94 m and L₂ = 1.28 m.

In the figure, rigid tee-beam ABC is supported at A by a single shear pin connection and at B by a strut, which consists of two 27-mm-wide by 5-mm-thick steel bars. The pins at A, B, and D are each 11 mm in diameter. The yield strength of the steel bars in strut (1) is 291 MPa, and the ultimate shear strength of each pin is 578 MPa. Determine the allowable load P that may be applied to the rigid bar at C if an overall factor of safety of 2.2 is required. Use L₁ = 0.94 m and L₂ = 1.28 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 7:The figure shows a truss. The truss use angle bar for every members. Members BD and CD and CE are angle sections and needed to fasten to a gusset plate. with the thicknesses of 14 mm. The working stresses are 80 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets.. 4 m 4m 3 m MATHalino.com 4m 360 KN 19. How many 19 mm diameter rivets are needed to use for member BD. Number of rivets must express in whole number 20. How many 19 mm diameter rivets are needed to use for member CD 21. How may 19 mm diameter rivets are need to use for member CE
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4 m and have a web width of 250 mm, an effective depth of 400 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-ϕ32 mm bars in two rows. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the ultimate bending moment strength of the T-beam in kN·m. 701 778 711 640
Problem 1 The cross-sectional area of each member of the truss is 1200 mm². Calculate the stresses in members AB, BC, DF, CE, and BD. A 4 m C 100 kN B 6 m 3 m 200 kN D 4 m E 3 m F
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4 m and have a web width of 250 mm, an effective depth of 400 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-ϕ32 mm bars in two rows. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the ultimate bending moment strength of the T-beam in kN·m. A. 640 B. 701 C. 778 D. 711
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
The center panel of the truss contains two flexible cables. What load P will cause a compressive force of 2000 N in BD? Then determine which tension diagonal BE or CD is acting and the force in it. B D R₁ L L L CLEL P R₂
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
Question 15 The design shear resistance, Vpl.Rd of a fully restrained simply supported Universal Beam with yield strength 345 N/mm² is 1,285 kN A point load of magnitude 1,906 kN is applied at the beam's mid-span The area of the web of the beam is Aw = 5,505 mm² The plastic modulus is Wpl.y = 2,979 cm³ The thickness of the beam web is tw = 12.6 mm Find the reduced design moment of resistance of the beam Mc,Rd (use the formula for l-cross-sections with equal flanges and bending about the major axis) Give your answer in kNm to the nearest whole number. Do not include units in your answer.
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
Q4: determine the maximum tensile and compressive stresses acting normal to the beam. 50 mm 10 kN 100 mm 30 kN 6 m 2m B (2