manage your time. Problem 1: (50 points) A 150 mm-diameter water jet sticks horizontally the 30° deflector as shown in figure below. The deflector covers a 125mm diameter hole in the tank wall on the right side. What is the maximum water depth H in the right tank that can be maintained the water without leaking? water 30 3m 150 mm dia water 125 mm dia jet 30

manage your time. Problem 1: (50 points) A 150 mm-diameter water jet sticks horizontally the 30° deflector as shown in figure below. The deflector covers a 125mm diameter hole in the tank wall on the right side. What is the maximum water depth H in the right tank that can be maintained the water without leaking? water 30 3m 150 mm dia water 125 mm dia jet 30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
As shown in the figure below, a Venturi meter is installed on a 300-mm diameter pipe whose maximum flow is 125 liters per second and the pressure head is 6.5 m of water. Determine the minimum throat diameter that will give a negative head. Solve for the discharge that will pass through the meter when the double column differential mercury gauge connected to it will show a difference of 25 cm. |25сm P. 36.5 h A2 300mmф Al ANSWER: a. D = 118mm b. Q = 87 liters/sec
300 mmg 100 mmø H2O, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss.
... 200mm 300mm diameter 450mm 30° 400mm 1 diameter Mercury (SG = 13.6) "X" 350mm Vate In the 200mm diameter vertical venturi meter attached to a 400mm pipe as shown, a manometer is attached to the side. If the discharge of water in the system is 300 L/s, determine the distance "x" shown. A) 208.41 mm B) 192.74 mm No Answer among the choices D) 226.32 mm E) 242.69 mm
Can Please Help Me: Civil Engineering 60 minutes only the given time. Wish you could help me. I will give UPVOTE and GOOD FEEDBACK. //Question A 2-foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with a slope of 0.8 foot per 90 feet. At the time of measurement, the pipe has 0.8 feet of discharge flowing in it. What is the pipe discharge? (Express your answer in liter per second). Ans.205.1 lps //Question
Orange JO l M O ☆ O N 94 |14 4:40 Hydraulic-2018_.. 0.915 04. A tank is constructed of a series of cylinders as/ shown in the figure. The tank contains: oil p,915 kg/m, water p 1000 kg/m', glycerin p,= 1300 A3 kg/m, mercury p-13600 kg/m'. A mercury manometer is attached to the bottom of the tank Calculate the manometer reading h oil water mercury P-P ig +8, Xo-+ 8 Xo. +8 i X - 8 xhm 13.6x9S1o xhm + 13 x96o Xo. + 981o Xo + 0.915 X0.1 - 13.6 x 9 s10 Xhm 131416 x h + 1275.3 + 981 13341 6Xhm + 0.0915 133416 Xhm 2256.4 %3D 13416 x hm
Fluid mechanis Read the question carefully, give me right solution The head loss (hf) in a 1200mm x 600mm pipe (therefore, non-circular) conveying water is estimated to be 0.04m for every 1 meter of its total length. If the said pipe is filled with water and its friction factor f = 0.032, what should be the discharge Q?
3. In Figure below, sensor A reads 2.5 kPa (gage). All fluids are at 10°C. Determine the elevations Z in meters of the liquid levels in the open piezometer tubes B and C (Yair 12 N/m?, Ygasoline * 6670 N/m2, Yglycerin 12360 N/m?) Sm Air 3 m Gasoline 1 m Glycernin
flow of water in the below diagram is from point X to Y. The oil is in the e inverted U-tube manometer. The mercury is in the bottom of the manome ressure difference P -P in kPa?
A 150 mm by 50 mm Venturi meter is installed in an inclined pipe carrying oil. The vertical distance between the inlet and throat is 20 cm. The flow is upward through the meter. A differential manometer containing mercury (sp. gr. = 13.6) is attached to the inlet base and throat. Compute the deflection of the mercury if the actual discharge thru the pipe is 0.055 m3/s. Assume the Venturi coefficient to be 0.97.
2. A vertical venturi meter, 150 mm in diameter is connected to a 300 mm diameter pipe. The vertical distance from the inlet to the throat being 750 mm. If the deflection of mercury in the differential manometer connected from the inlet to the throat is 360 mm, determine the flow of water through the meter if the meter coefficient is 0.78. Determine also the head lost from the inlet to the throat 300 mm Ø 750 mm 150 mm O 360 mm
600mm water diameter 300mm 1. diameter 02 150mm Mercury (SG = 13.6) A venturi meter with diameter of 300mm is attached to a 600mm main pipe and has its axis inclined downward as shown. a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 500mm from point 1 to 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3 The manometer shows a deflection of 15cm of mercury (SG =13.6). If the flowing fluid is water and direction is from 1 to 2, determine the