Problem 1-53: The bar has a cross-sectional area of 400(106) m². If it is subjected to a uniform axial distributed loading along its length of 9 kN/m, and to two concentrated loads as shown, determine the average normal stress in the bar as a function of x for 0.6 m < x≤ 1.5 m. -0.6 m 8 kN 0.9 m 4 kN

Problem 1-53: The bar has a cross-sectional area of 400(106) m². If it is subjected to a uniform axial distributed loading along its length of 9 kN/m, and to two concentrated loads as shown, determine the average normal stress in the bar as a function of x for 0.6 m < x≤ 1.5 m. -0.6 m 8 kN 0.9 m 4 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.14P: The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind...

See similar textbooks

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in Ib/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in. 12 in.- 16 in: CAR = units %3D II
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 70 mm and a wall thickness of 3 mm. Determine the normal stress in each truss member. Assume P-12 kN, Q - 17 kN, a- 1.4 m, b -3.6 m, and c-1.3 m. Use positive for tensile stress and negative for compressive stress. Answers: OAB- JAC- OBC- i B (3) b MPa. MPa. MPa.
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The masonry pier is subjected to the FFF = 810 kNkN load. Consider xx = 0.25 mm and yy = 0.5 mm. Neglect the weight of the pier. Determine the normal stress at corner A. Determine the normal stress at corner B. Determine the normal stress at corner C.
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in lb/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in: 12 in. 16 in: CAR= units II II
7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips. Figure P-106 3 m 5 m 5 m E
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
Current Attempt in Progress The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w-70 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot ex t exceed 100 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pax that can be supported by the structure. Answer: Pax 3 KN
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
A guy wire for an antenna tower is to be alumi- num, having an allowable stress of 12 000 psi. If the expected maximum load on the wire is 6400 lb, determine the required diameter of the wire. 3-7.
X A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section at a-a has a diameter of d = 3 mm and the hook is supporting a purse with a mass of 3 kg, determine the normal stress profile. For what value of y (using the coordinates pictured for section a-a) with the normal stress be zero. If it is never zero enter "nde" for "not defined". N -L→ a. a AB C Follow sign convention that tension is positive and compression is negative. Normal stress at point A, σA= MPa Normal stress at point B, σB = MPa Normal stress at point C, σc = MPa y position where normal stress equals zero = mm Section a-a d