Q1 a. Identify a real life device/control system application configured as Open-loop Control System and provide the required descriptions as listed in the question. i. Discuss functionality and usefulness of the device. ii. Draw the essential parts using block diagram and label each block. iii. Describe the specific function of each block

Q1 a. Identify a real life device/control system application configured as Open-loop Control System and provide the required descriptions as listed in the question. i. Discuss functionality and usefulness of the device. ii. Draw the essential parts using block diagram and label each block. iii. Describe the specific function of each block

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Can someone help me with this just need a P&ID solution meeting the requirements and explanation. thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 1:Cold liquid continuously flow in a tank where its temperature is maintained at 90° C.Steam passes through the tubing which supplies energy for heating. Requirements: One feedback solution One feedforward solution PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution PROCESS 3: Product is charged in a closed, jacketed reactor where it is stirred. The reactortemperature is controlled through the uninterrupted flow of coolant in the…
a. Currently, you serve as a robotic engineer by a company, and your boss want you to design a robot in spatial space to satisfy the following conditions: i. Max reachable distance of the robot is 1 meter. ii. Only using revolute joints, connecting links and rigid load bearing links (the length of link is 0.5m). iii. The degree of freedom (Dof) of the robot is 2. What is your design, how many joints and links will you use? b. The payload of your design is 10 kg (each load bearing link can hold 5 kg, 5 kg+5 kg=10kg, the weight and payload of the connecting links will be ignored), but your boss wants your designed robots to handle 20 kg payload. How will you update your current design, and how many joints and links will you use in the new design? What is the Dof of the new designed robot.
exam_question.php?exam_id: Some computers contain multi-processors in order to s1 /4 MS-DOS considered as the weakest OS because of It
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
Using signavio or any PBM tools and must Use pool and lane and object. Model the following business process at a supplier. After a supplier notifies a retailer of the approval of a purchase order, the supplier can receive an order confirmation, an order change, or an order cancelation from the retailer. It may happen that no response is received at all. If no response is received after 48 h, or if an order cancelation is received, the supplier will cancel the order. If an order confirmation is received within 48 h, the supplier will process the order normally. If an order change is received within 48 h, the supplier will update the order and ask again the retailer for confirmation. The retailer is allowed to change an order at most three times. Afterwards, the supplier will automatically cancel the order.
using Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion
Suppose that four machines, 1, 2, 3, and 4 have been identified as belonging in a Group Technology (GT) machine cell. 50 parts enter the machine grouping at machine 3, 20 parts leave afterprocessing at machine 1, and 30 parts leave after machine 4. Determine a logical machine arrangement through cluster analysis.
using: Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion find
CTD and BOM are one-to-one related to each other regarding the abstraction levels: False True
Using "Subjective Digital Design", please develop the Boolean equation for the problem statement given: This CNC machine controller allow operation (represented by O) of the machine if there is a part in the vice (determined by a sensor P) and the spindle is fully retracted (determined by another sensor R) or a manual override (M) button is pressed by the operator.
Application first order
The main reason to do Design for Manufacturing (DFM) is? O a. To predict costs O b. To improve the design of the products Oc To predict time O d. To estimate cost evaluation for further system analysis: