Q3) A rigid bar AB is hinged at A and supported by a copper rod 2m long and steel rod 1 m long. The bar carried a load of 65 kN at B as shown in Fig. below, if the cross section area of steel and copper rods are 250mm^2 and 500 mm^2 respectivlley. Determine the stress developed in each rod. (take Es=200 GPa, Ec= 100 GPa) A munu Steel rod- 1 m 1 m- 2 m Copper rod 2 m B 65 kN

Q3) A rigid bar AB is hinged at A and supported by a copper rod 2m long and steel rod 1 m long. The bar carried a load of 65 kN at B as shown in Fig. below, if the cross section area of steel and copper rods are 250mm^2 and 500 mm^2 respectivlley. Determine the stress developed in each rod. (take Es=200 GPa, Ec= 100 GPa) A munu Steel rod- 1 m 1 m- 2 m Copper rod 2 m B 65 kN

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A steel bar AD has a cross sectional area of 250 mm^2 and is loaded by a force P1= 5KN, P2 = 10KN and P3 = 6KN. The lengths of the segments are a= 1.5m, b=0.60m, and c=0.90m. E=200,000 MPa. a.) Calculate the change in length of the bar. b.) Determine the stress of member BC. c.) By what amount should the load P3 be increased so that the bar does not change in length when the three loads are applied.
1. An aluminum tube is rigidly fastened between a bronze rod and steel rod as shown in thefigure. Axial loads are applied at the positions indicated. Determine the stress in each material.
The blue atoms are corners • The yellow atoms are face atoms The green atoms are fully inside the unit cell diamond/zincblende molecule Consider the unit cell for a diamond/zincblende molecular structure shown. The value of a = 7.92 X 10^(-8) cm. a Use the figure and information shown to determine the number of atoms per cubic cm. When your group has agreed on the answer, enter it in the comment box. Include units in your answer!
Consider the infinite wire carrying current of 2 A along positive y-direction. The other wire is carrying current of 1A along positive x direction from x= 4 m to x = 12 m. Calculate the force exert on second wire from the first wire. (a) 3.634x107 N (b) 4.394x10 N (c) 7.216x107 N (d) 9.631x107 N
1 cm. of copper with - charged sphere originally placed at P when it has travelled a great distance from P? Assume the mass of the sphere is Img and carries a charge of +3 C allo udadD le ool od ts booel sd goirigb davinail on 3. For the circuit below, use Kirchoffs Law(s) to write to down the equations needed to solve for the currents through each resistor. Note that for every unknown current you need an equation. However, you need not solve your equations for the unknown currents. Iit I 3=Iz L, = 18 V 0.52 R 2.5 0- R, e a 6.0 2 R 1.52 sil oools orit lo sbutinga 0.50 Ez = 45 V Send a chat
The force between two parallel conductors carrying currents in opposite direction is 3.776 N/m when they are placed 59 mm apart in air. If current flowing in one conductor is 1,180 A, solve the current in the other conductor. Draw the diagram. thank u
The permeability of a low-carbon steel is μ=2x10-4 Wb/At.m The shape of this material is a torus (looks like a doughnut), with an inner radius ri=1.75 cm and outer radius ro=2.25 cm. Calculate its reluctance. A. 11.9 x10-4 At/Wb. B. 21.9 x10-4 At/Wb. C. 31.9 x10-4 At/Wb. D. 41.9 x10-4 At/Wb
The force between two parallel conductors carrying currents in opposite direction is 3.2 N/m when they are placed 50 mm apart in air. If current flowing in one conductor is 1000 A, a. solve the current in the other conductor b. solve the current in the other conductor if force is change to 5.8 N/m
A 25 mm square cross-section bar of length 300 mm carries an axial compressive load of 50 kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 GN/m².
if a solenoid wire is 100ft long with 2000 turns in a bobbin with length between gap and and metal 0.1m and 30amps a)find newton of force of solenoid at 30amps 25v & .833 wire resistanceb) find wire cross sectional area ..
The electromagnet shown in the Fig. below is to be used to lift an iron slab of mass M=150 kg. The surface roughness of the iron is such that when the iron and the electromagnet are in contact, there is a minimum air gap of 0.2 mm in each leg. The electromagnet has infinite permeability and the crosssectional area Ac is 25 cm2. The number of turns of N-turn winding is 350 and the winding coil resistance is 3 Ω. Calculate the minimum coil voltage which must be used to lift the iron slab against the force of gravity. Neglect the reluctance of the iron.(Hint: Gravitational acceleration constant is 9.8 m/s2)
The inductive reactance, X,, of a coil is given by X, = 27nfL, where f is the frequency and L is the inductance. If the inductive reactance is 345 V and the frequency is 90.0 cycles/s, find the inductance L in henrys, H. (Use the rules for working with measurements to give your answer to the appropriate accuracy and/or precision.) L = H Need Help? Read It Submit Answer V 1 10:56 Co & %23 6. e