Q8/Assume that the microprocessor can directly address 64K with a R/W' and 8 data pins The memory map for 16K x 8 RAM system that design by * using 4KX8 RAM are E7FF-E700 ,D7FF-D700 ,B7FF- B700 ,77FF-7700 EFFF-E000 , DFFF-D000 ,BFFF- BO00 ,7FFF-7000 EFFF-E000 ,DFFF-D000 ,BFFF- BO00 ,AFFF-A000 None of them E7FF-E700 ,D7FF-D700 ,B7FF- B700 ,A7FF-A700

Q8/Assume that the microprocessor can directly address 64K with a R/W' and 8 data pins The memory map for 16K x 8 RAM system that design by * using 4KX8 RAM are E7FF-E700 ,D7FF-D700 ,B7FF- B700 ,77FF-7700 EFFF-E000 , DFFF-D000 ,BFFF- BO00 ,7FFF-7000 EFFF-E000 ,DFFF-D000 ,BFFF- BO00 ,AFFF-A000 None of them E7FF-E700 ,D7FF-D700 ,B7FF- B700 ,A7FF-A700

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). 8. gf a b t la Ob d Dp e d8c Dp The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be OFF while all the others are ON. 1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input (000.101), assuming the other two combinations as don't care. 2- Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions 3- Show your design using 2-input, and 3-input NAND gates, and inverter.
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
8:37 4 A M Vo) Gt LTE1 You Just now i) Analyse and execute the following 8051 Instructions and specify the output and explain the contents of the registers with comments MOV A, #92H SWAP A In the absence of a SWAP instruction, how would you exchange the nibbles? Write an 8051 ALP to show the process ii) Analyse and execute the following 8051 Instructions and specify the output and explain the contents of the registers with comments. CLRC MOV A, #4FH SUBB A#6DH JNC NXT CPL A INC A NXT: MOV RI,A ADD A,RI
in Intel 8086 microprocessor, the memory address for the code segment 771Fh and offset 3584 h is O 7A774 3CF5F О АСАЗО OACA3 in Intel 8086 microprocessor, the memory address for the code segment 3021 h and offset 21D7h is 323E7 51F80 051F8 24D91
Consider a 4-bit ADC and full scale voltage measurement range of (-37 to 37).The Resolution will be O 4.62 O 1.75 O 0.41 O 0.41 In CRO, if the electron beam emerging from the electron gun is left alone, it will strike the screen as straight line. Select one: OTrue O False
An Intel 8085 processor is executing the program given below. MVI A, 10H MVI B, 10H BACK NOP : ADD B RLC JNC BACK HLT The number of times that the operation NOP will be executed is equal to
Write an assembly 8051 code to count a hexadecimal digit every second and display it on the 7-segment.
For the cct shown below find zt and drow the equivalent cct IPD I Cgdp RE Cgdn CPD VDD Mp Ma HH Figure 5. Schematic diagram of the Inv-TIA. Cout
onal clock cycles form one bus cycle. ROM can be classified into Dynamic ROM and Static ROM. Select one: O True O False Auxillary carry flag will be set whenever O a. there is a carry from lower nibble to higher nibble as well as borrow from higher nibble to lower nibble O b. there is a carry from higher nibble to lower nibble Wingos there is a borrow from lower nibble to higher nibble C. OlacVl Jal none of the choices are correct
1-Write microprocessor program using mnemonics to add two numbers 08 and 06. 2-Write the object code of the program. 3-Perform the program using STEP function. 4-Execute the program and write the results. Object code Mnemonics MOV AX A1 B0 MOV AL B3 MOV BL 04 ADD AL F4 HLT
Draw logic diagram for half adder and full adder circuit using Logisim Software
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef