R=652 X₁ = -852 wwwmm a. I-20A a. b. C. 13. The power consumed in the circuit shown in fig. 1 is. a. 4000W b. 2400W 200V C. 2000W d. 1200W 14. The reactive power drawn by the circuit shown in fig. 1 is Figure 1 a. 2400VAR b. 4000VAR 'C. 3200VAR d. 2000VAR 15. The active component of line current in figure 1 is 12A 20A 12A 4A

R=652 X₁ = -852 wwwmm a. I-20A a. b. C. 13. The power consumed in the circuit shown in fig. 1 is. a. 4000W b. 2400W 200V C. 2000W d. 1200W 14. The reactive power drawn by the circuit shown in fig. 1 is Figure 1 a. 2400VAR b. 4000VAR 'C. 3200VAR d. 2000VAR 15. The active component of line current in figure 1 is 12A 20A 12A 4A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
Electromechanical Engineering Dept. First Class lecture 4 it Dr. Ekbal H. Example/ The FWR cct. shown in Fig.below draw output wave form. Then find i. DC voltage and current ii. the ripple voltage iii. ripple factor. iv. Change in DC voltage if capacitor increased to 100 uF Vintmsj=220 v F 50 Hz V. Ns/Np=1/5 R=10K2 C=50 uF TL
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
Calculate the average and the root-mean-square value of the output voltage for the network in the figure below. Assume (VDI=VD2=0.5V) 10 V D2. D1 2k2 I t 3k2 3 k2 O 2.417V, 2.687V 2.421V, 2.736V 2.536V, 2.657V 2.173V, 2.824V O 2.517V, 2.876V O 2.714V, 2.766V
•A system consists of ,The electric potential opplied to this cell droes o cubie cell, to 1oV from 30OV in one step. •Whot is the hork done? •Whot wald the work done be if it hernt from 3or to 20v and then to lov?
The waveforms below represent one full cycle of the applied voltage vs and the supply current is. based on the waveforms below, which of the following statements is true. options: is leads vs is lags vs is is in phase with vs
Ministry of Manpower Directorate General of Technological Education Salalah College of Technology Zlectrical Inginearina Problem - 8 Refer to the circuit below and -25V C2 N. compute the following: i) Total capacitance ii) Voltage across C, iii)Charge across C, iv)Voltage across C5 5 uF C1 5 uF 5 uF C4 5 uF C6 5 uF -16-65V. C5 5 uF (Take V, as 25V) 8-35V VT 25V
Choose the % derating factor of the string which is having 8 number of SCR connected in series to withstand a DC voltage of 1864 V and steady state voltage rating of 803 V. O a. 5.38 Ob. 14.51 Oc 70.98 O d. 29.02
A 1500 W heating elements at an initial temperature of 15 C is connected to supply voltage of 115V. After the temperature of the element has stabilized steady state condition it is found that the voltage of 125V is required to maintain the rated output. If the temperature coefficient at 15C of the element is 0.0006 per C determine the element of the final temperature. 317C 310C 307C 323C
Given the following find: The reactive power dissipated by the source is (in Vars) The apparent power dissipated by the source is (in VA)
Time left 0 A resistor of 42 ohm is connected in series with a capacitor of 50 micro farad. if a supply of 240 V, 60 Hz is connected across the arrangement then the current flowing in the capacitor is. O a. 3.14 A O b. 35.4 A O c. 31.4 A O d. 3.54 A
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current