Task 1: A dam is used to store water, and a circular gate which is hinged at its bottom edge is used to control the flow as shown in figure 1. A pressure of 300 kPa is applied to the water free surface. For this gate, width=1 m (in the direction of the page), hị =1 m, and h2 = 6 m. P = 300 kPa hi Water Atmospheric pressure Gate hz

Task 1: A dam is used to store water, and a circular gate which is hinged at its bottom edge is used to control the flow as shown in figure 1. A pressure of 300 kPa is applied to the water free surface. For this gate, width=1 m (in the direction of the page), hị =1 m, and h2 = 6 m. P = 300 kPa hi Water Atmospheric pressure Gate hz

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
A 200 mm steel pipe is connected to a reservoir as shown in the figure. A 200 mm x 50 mm nozzle at the end of the pipe discharges a jet. Determine the flow rate and the pressure at points A, B, C, and D. Ignore losses
A storage tank contains a liquid at depth y where y=0 when the tank is half full. Liquid is withdrawn at a constant flow rate Q to meets demands. The Contents are resupplied at a sinusoidal rate 30sin (t). Equation can be written as: d(Ay) = 3Q sin?(1) – Q (1)p (change in` (inflow) – (outflow) volume since the surface area A is constant sin²ce) – O A dy d(t) Use Euler's method to solve for the depth y from t = 0 to 10 d with a step size of 0.5 d. The parameter values are A = 1200 m? and Q = 500 m/d. Assume that the initial condition is y = 0.
Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the figure below. Assume SG = 0.92. Ah = m 1m SG Water 0.4 m Z Ah
1. Water is flowing in a wide open channel as shown in the figure. Two pitot tubes are connected to a different manometer containing oil (sp.gr. = 0.82). Find the velocity at m point A and point B in - oil (op.gr.=0.82) 2 m wafer sarfece
The figure given below is a storage tank that contains a liquid at depth y, where y = 0 when the tank is half full. Liquid is withdrawn at a constant flow rate Q to meet demands. The contents are replenished at a sinusoidal rate 3Q sin?(t). Suppose that the outflow is not constant but rather depends on the depth. The differential equation for depth can be written as dy a(1+ y)125 = 3 sin?(t) dt A A y Use Euler's method to solve for the depth y from t= 0 to 10 d with a step size of 2 d. The parameter values are A = 1250 m², Q = 425 m³/d, and a = 175. Assume that the initial condition is y(0) = 0. (Round the final answers to five decimal places.)
The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses in the system what is the flow rate for Az = 97 m if the pipe has the following properties: • L = 7 km • D = 50 mm ΔΖ L, d, E (a) What is the friction factor? Please provide your answer to 2 significant figures. Number (b) What is the flow rate? Please provide your answer to 3 significant figures. Number Units D
In the illustration: A 1 C All friction factor f = 0.02 All pipe lengths L = 250m Diameter of Pipe A = 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.
Problem #4 If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate? The pipes are galvanized iron with 0.0005 ft. Take v = 1.06 × 10−5 ft²/s and neglect Kis = minor losses. 10 in. dia 1. 2000 ft, 8 in. dia A B 1600 ft, 6 in. dia с 2. 800 ft, 10 in. dia-
The pump shown in the figure below delivers a head of 200 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L = 300 ft, D = 0.75 ft. Ws = S HKL IN valve Pump = 5.0 KL=0.8 KL = 1.5 Pipe length = L Pipe diameter = D Pipe roughness=0 ft-lb/s or K₁ i Lexit 1.0 hp
ASAP
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to (a) 26 cm (c) 76 cm Patm 144.444 Hg= (b) 50 cm (d) 126 cm arter