The 40-kg uniform triangular plate is supported by two small hinges A and B and the cable system shown. For the horizontal position of the plate, determine all hinge reactions and the tension T in the cable. Hinge A can resist axial thrust, but hinge B cannot. See Table D/3 in Appendix D for the mass-center location of a triangular plate. 0.20 0.43 m 0.43 m. 0.20 m Answers: Ax= Ay- A₂- By B₂- T= 0.91 m zzzzz N N N N N N 1.30 m С

The 40-kg uniform triangular plate is supported by two small hinges A and B and the cable system shown. For the horizontal position of the plate, determine all hinge reactions and the tension T in the cable. Hinge A can resist axial thrust, but hinge B cannot. See Table D/3 in Appendix D for the mass-center location of a triangular plate. 0.20 0.43 m 0.43 m. 0.20 m Answers: Ax= Ay- A₂- By B₂- T= 0.91 m zzzzz N N N N N N 1.30 m С

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
A smooth inclined plane has a gradient of 1 in 6. Calculate the mass of a body that can be held in equilibrium on the plane by a force of 80 N when the force acts: (a) parallel to the plane answer M=49.62kg (b) horizontally answer M=48.94 kg (c) at an angle of the 20° with the plane. answer M=46.62kg
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 14j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. %3D 2 m C 4 m 6 m y Answer: Calculato the madnitude of the tension in cable BD in kN. ere to search 3m 6m
For the system shown, if taking the frame as free body, how many forces should you consider in the FBD? 3.75 ft 17.5 ft 5 ft 65 W= 10 I 10ft 3600 lb Answer:
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
For the frame shown below, The mass of the object connected is 96-kg. what is the value of the force in member BC in N? (Note: enter your numeric answer only. No need to enter units. Give your answer to three decimal places and negative for compression). FBC = -1.2 m 0.1 m 0.3 m В C 0.6 m A