The Biot number during a heat transfer process between a sphere and its surroundings is determined to be 0.02. Would you use lumped system analysis or the transient temperature charts when determining the midpoint temperature of the sphere? Why?

The Biot number during a heat transfer process between a sphere and its surroundings is determined to be 0.02. Would you use lumped system analysis or the transient temperature charts when determining the midpoint temperature of the sphere? Why?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.19P: 1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the...

See similar textbooks

Related questions

Q: Consider a 1.2-m-high and 2-m-wide glass windowwith a thickness of 6 mm, thermal conductivity k =…

A: Given data Length of the plate L = 1.2 m width of the plate = 2 m thickness of the plate t= 6 mm…

Q: what factors play a vital role in maximizing the convection heat transfer coefficient ?

A: convection heat transfer coefficient of Heat and mass transfer

Q: Consider a 0.8-m-high and 1.5-m-wide double-pane window consisting of two 4-mm-thick layers of glass…

A: Heat transfer is directly proportional to the temperature difference and inversely proportional to…

Q: Question # 2: A10-m-long section of a 6-cm-diameter horizontal hot water pipe passes through a large…

A: Given data as per the question Length of section =10 m diameter =6 cm Tmean=65+222=43.50cconsidering…

Q: The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and 8…

A: Given datavelocity=70 km/hrDimension of car=2.8m*8 msolar radiation=200 w/m2temperature of…

Q: The vertical 0.8-m-high, 2-m-wide double-pane window consists of two sheets of glass separated by a…

A: The properties of air are given as – Calculating Grashof’s number

Q: Determine the temperature of the air film adjacent to a wall with a temperature of 30 deg C, the…

Q: What is the product solution method? How is it used to determine the transient temperature…

A: Product solution method is a super position method which is used in one dimensional heat conduction…

Q: A Ball is heated to a temperature of 100°F throughout and is allowed to cool in ambient air at Temp…

A: When a temperature gradient exits perpendicular to the area, thermal conductivity is defined as the…

Q: In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the…

Q: Define Nusselt (Nu), Prandtl (Pr), Reynolds (Re) and Grashof (Gr) dimensionless numbers. State which…

A: Nusselt number represents the enhancement of heat transfer through a fluid layer as a result of…

Q: [2] Consider a 1.2-m-high and 2-m-wide double-pane window consisting of two 3-mm-thick layers of…

Q: Why is heat transfer faster in forced convection compared to natural convection

A: Natural convection: when heat transfer is taking place due to motion of fluid caused by density…

Q: 4. A car engine with the dimensions 0.6 m high, 0.50 m-wide, and 0.8-m- long. The bottom surface of…

Q: Consider a 0.8-m-high and 1.5-m-wide double-pane window consisting of two 4-mm-thick layers of glass…

A: Drawing network diagram Kn= 0.78 w/m°c Ka = 0.026 w/m°c La= 10mm= 0.01m Lw= 4mm= 0.004m T ∞1i= 20°c…

Q: What is a semi-infinite medium? Give examples of solid bodies that can be treated as semi-infinite…

A: A semi-infinite solid : It is idealized body that has single plane surface & extends to infinity…

Q: calculate the convection heat transfer rate over a surface of area 1 m^2 having heat convection…

A: GIven Data Surface area , As=1m2. Heat convection coefficient, h=40 W/m2K Temperature difference,…

Q: A 0.2-m-long and 25-mm-thick vertical plate (k = 1.5 W/m∙K) separates the hot water from the cold…

A: Fourier's Law:- According to Fourier's law, the rate of heat transfer through conduction is given…

Q: Consider a sphere and a cylinder of equal volume made of copper. Both the cylinder and sphere 'are…

A: The answer is in next step

Q: QO What are the types of convection heat transfer?

A: Heat transfer takes place in three types 1. Conduction 2. Convection 3. Radiation

Q: The boiling temperature of nitrogen at atmosphericpressure at sea level (1 atm) is -196°C.…

A: The rate of heat transfer during evaporation of nitrogen, The rate of heat transfer from the…

Q: QI/The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and…

A: Given data: v=70 km/h=19.44 m/sqrad=200 W/m2L=8 mT∞=30°C Need to determine the equilibrium…

Q: Consider heat transfer between two identical hot solid bodies and their environments. The first…

A: The lumped analysis system is mostly applied for the bodies which are allowed to cool in the air. A…

Q: A 18-m-long section of a 14-cm-diameter horizontal hot water pipe passes through a large room whose…

Q: Consider a room with a 1.8-m-high and 2.0-m-wide double- pane window consisting of two 4-mm-thick…

A: Given: T1 = 22 deg C T2 = -4 deg C There are total five resistances are acting.

Q: An average person generates heat at a rate of 240 Btu/h while resting in a room at 70°F. Assuming…

A: The rate of heat transfer, Q = 240 Btu/h The room temperature, Ts = 70°F The emissivity of the skin,…

Q: A long 2-in-diameter rod with surface temperature of 200°F is submerged in a bath of fluid.…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: 1] During a plant visit, it was noticed that a 12-m-long section of a 10-cm-diameter steam pipe is…

Q: Define the cooling of a boiled egg by forced and natural convection.

A: Rate of heat transfer by convection is given by Where h is convective heat transfer coefficient.…

Q: Determine the steady rate of heat transfer

Q: Consider a 1.2-m-high and 2-m-wide double-pane window consisting of two 3-mm-thick layers of glass…

Q: Consider a cold aluminum canned drink that is initially at a uniform temperature of 4°C. The can is…

Q: Consider a 1.1-m-high, 0.4-m-diameter vertical vessel which is located in a large room whose…

Q: Consider a hot automotive engine, which can be approximated as a 0.5-m-high, 0.40-m-wide, and…

A: Given data as per question Height of automobile = 0.5m Width of vehicle =0.4 m Length of vehicle=0.8…

Q: The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and 8…

A: The properties of the air at the 30 degrees Celsius are,

Q: 1) Determine the convection heat transfer coefficient and the heat flux on the plate surface for…

Q: An electric resistance space heater is designed such that it resembles a rectangular box 50 cm high,…

A: Consider the diagram shown below for the given heater. The mean film temperature is The properties…

Q: In free convection heat transfer, Nusselt number is function of А. Grashoff number and Reynold…

A: Ans: option(B) Reason: in free convection heat transfer, Nusselt number is function of Grashoff…

Q: A person is found dead at 5PM in a room whose temperature is 20°C. The temperature of the body is…

A: Given, Diameter,d=30cm=0.30mradius, r=0.15mLength, L=1.70mHeat transfer coefficient,…

Q: When a flat plate is subjected to uniform heat flux, how different are the relations compared to the…

A: To Explain : How different are the relations compared to the isothermal plate case. Formula used:…

Q: Consider a 0.8-m-high and 1.5-m-wide double-pane window consisting of two 4-mm-thick layers of glass…

Q: Consider a room with a 1.8-m-high and 2.0-m-wide double-pane window consisting of two 4-mm-thick…

Q: Illustrate the concept of convection in heat transfer operation and also differentiate forced…

A: Convection Convection is a mechanism of energy transmission that combines the combined effects of…

Q: Consider a 1.2-m-high and 2-m-wide double-pane window consisting of two 3-mm-thick layers of glass…

Question

The Biot number during a heat transfer process between
a sphere and its surroundings is determined to be 0.02. Would
you use lumped system analysis or the transient temperature
charts when determining the midpoint temperature of the sphere?
Why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
When a flat plate is subjected to uniform heat flux, how different are the relations compared to the isothermal plate case? Questions above are related to Heat transfer
During hot summer weather, many people put “koozies” around their beverages to keep the drinks cold. In addition to preventing a warm hand from heating the container through conduction, what other mechanisms slow the process of warming beverages?
To ensure that the balls bounce consistently, tennis balls in Wimbledon are stored at exactly 68oF. A ballboy keeps a ball in his pocket to ensure that the ball can be given to the player quickly. If the ball is observed to warm up to 70oF after one minute, how long will it take for the ball to be within 20oF of the ballboy's body temperature (98.6oF) after he puts it in his pocket? It can be assumed that the temperature in the pocket is also the normal body temperature.
Hi, can you help me to answer this question using the first law of thermodynamics formula to explain this event? On a hot summer day, a student turns his fan on when he leaves his room in themorning. When he returns in the evening will the room be warmer or cooler than theneighborouing rooms ? Explain your answer using the first law of thermodynamics.Assume ALL doors and windows are kept closed.
In presence of an external flow when will the convective heat transfer be dominated by free convection and not by the forced convection due to the external flow? Gr ≫ Re². Gr ≪ Re. Gr ≫ Re. Gr ≪ Re For ideal gases, the specific heat capacity at constant pressure, thermal conductivity, dynamic viscosity, and Prandtl number are independent of pressure. How will the ratio of thicknesses of velocity boundary layer and thermal boundary layer change if pressure is increased from 1 atm to 5 atm for the flow of an ideal gas over a flat plate? It will decrease by a factor of 5. It will remain the same. It will increase by a factor of 5. We need to know the actual fluid properties to tell.
what are the different modes of heat transfer? Explain transfer of heat by convection process?
Define the cooling of a boiled egg by forced and natural convection.
Volumetric thermal expansion is used in modeling natural convection heat transfer. Derive an expression for volumetric thermal expansion coefficient for an ideal gas.
Hi, can you help me to answer this question using the first law of thermodynamics? On a hot summer day a student turns his fan on when he leaves his room in themorning. When he returns in the evening will the room be warmer or cooler than theneighborouing rooms ? Explain your answer using the first law of thermodynamics.Assume ALL doors and windows are kept closed.
Heat transfer is a discipline of thermal engineering that concerns the generation, use, conversion,and exchange of thermal energy (heat) between physical systems. How do you connect it with thermodynamics and why is it necessary for us, mechanical engineers, to study it?