The circular shaft AB consists of a 22 mm diameter solid steel cylinder in which a 6 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 51 Nm. Determine the ratio of lengths L₁/L2. Input your answer to two decimal places. 4₁ C A 150 Nm L₂ 1

The circular shaft AB consists of a 22 mm diameter solid steel cylinder in which a 6 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 51 Nm. Determine the ratio of lengths L₁/L2. Input your answer to two decimal places. 4₁ C A 150 Nm L₂ 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m . The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm . The material have modulus of rigidity G = 143 Gpa. Answer the following questions
The axis ABCD receives a torque of 500Nm from the motor and transmits movement to other devices, by means of belts and pulleys connected at B and C. If it is known that the torques exerted on pulleys B and C are as shown In the figure, determine the minimum radius the shaft must have. You should consider that at point D of the motor there is a bearing that acts as a support for the shaft as at point A. The material of the shaft and its allowable shear stress are indicated in the drawing.Determine:to. Free-Body diagram.b. Shear force diagrams.c. Bending moment diagrams.d. Identification of the critical point of the axis.e. Calculation of the axis radius. tperm=80MPa
1. The 40-mm-diameter steel shaft is subjected to the torques shown. Determine the angle of twist of end B with respect to A. Use the sign convention for internal torques and take G= 75GPa. FBDs of cut sections OR an internal torque diagram is required for full credit. 80 N-m 20 N-m 30 N-m 600 mm 800 mm 200 mm
A steel shaft of diameter 60 mm and length 3.5 m is fixed at its ends A and B. If two torques of the same direction are applied, a 500 Nm torque at C (Im from the left end) and a 200 Nm torque at D (1m from the right end), determine the maximum internal torque in the shaft.
The answer is 1290N, but I am not entirely sure how they got there. However, I noticed that when I calculated the torques for the person and that of the ladder, my answer would be correct if I multiplied by sin(60) or cos (30) instead. Using the sum of these values, I would divide it by the length of the ladder and sin(30), which would give the correct answer, but I'm a bit confused as to why I need to take sin(60) or cos(30) to calculate the torques for the weight of the ladder and the human, but then use sin(30) when calculating the torque for the perpendicular force. I would appreciate a work through of the problem and some explanation for my difficulties above, thank you.
3. The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500N -m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm 4. A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 x 106 psi for aluminum. +4 in. → 0.04 in. 0.08 in.´ 5. Two steel springs are arranged in series as shown. The upper spring has 36 turns of 100-mm- diameter wire on a mean radius of 350 mm. The lower spring consists of 24 turns of 75-mm diameter wire on a mean radius of 245 mm. If the ultimate shearing stress in either spring must not exceed 692 MPa, (a) compute the maximum value of P and total elongation using factor of safety equal to 1.5. (b) What is the equivalent spring constant? Use G = 83 GPa. 2 of 2 4 in. wwwww.-
The ends and gears connected to the steel shaft (G = 75 GPa) aresubject to the torques shown. Determine the torsional angle of end B with respect to A.The shaft has a diameter of 40 mm.
PLEASE ANSWER ?? ?Part 1 Calculate the polar moments of inertia in segments (1) and (2). Please Answer: J₁ = in.⁴ J₂= in. ⁴ ?Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Please Answer: T₁ = Ib-ft, T₂= Ib-ft. ?Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Please Answer: τ₁ = psi, τ₂ = psi ?Part 4 Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. ?Part 5 Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad. Thank you so much in advance
The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1168.7 Nm, U = 4515 Nm, x = 3.01 m, y = 2.36 m, z = 1.35 m, d = 90 mm, and e = 83 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places. U T Aluminum Steel Bronze
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 261 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 194 mm in diameter. If the torque that can be applied is 8728 Nm without exceeding a shearing stress of 52.59 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places. Add vour answer
PLEASE ANSWER PART 4 and 5 Part 1 Calculate the polar moments of inertia in segments (1) and (2). Answer: J₁ = 13.84 in.⁴ J₂= 1.535 in. ⁴ Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Answer: T₁ = 800 Ib-ft, T₂= -800 Ib-ft. Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Answer: τ₁ = 1560.69 psi, τ₂ = -7817.59 psi Part 4 (PLEASE ANSWER) Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. Part 5 (PLEASE ANSWER) Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad.