The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m 2 m 300 N/m 2 m 1 of 1 Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. 8p=17.3 μÃ mm Submit Previous Answers Request Answer Provide Feedback ? * Incorrect; Try Again; 5 attempts remaining

The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m 2 m 300 N/m 2 m 1 of 1 Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. 8p=17.3 μÃ mm Submit Previous Answers Request Answer Provide Feedback ? * Incorrect; Try Again; 5 attempts remaining

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.7P: Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
The composite simply supported steel shaft is subjected to a force of 2P2PP = 16 kNkN at its center. EstEst = 200 GPaGPa. (Figure 1) A 200 mm 200 mm P AmaxAmax = 200 mm 40 mm P 200 mm 20 mm B Part A Determine the maximum deflection of the shaft. Express your answer to three significant figures and include the appropriate units. Enter positive value if the deflection is upward and negative value if the deflection is downward.
The beam is horizontal and the springs are unstretched when there is no load on the beam. Suppose that k = 1 kN/m and kB = 2 kN/m (Figure 1) Figure KA 00000 3 m 600 N/m 3 m B - ANNA < 1 of 1 KB D Part A Determine the angle of tilt of the beam when the load is applied. Express your answer in degrees to three significant figures. 17 ΑΣΦ 0= 0.052rad Submit vec Provide Feedback Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining ?
The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 12 mm² and is made from 6061-T6 aluminum (Eigure 1) Figure 1.5m 1011 300 N/m Y Part A Determine the vertical deflection of the bar at D when the distributed load is applied Express your answer to three significant figures and include the appropriate units. HA op= Value Submit Request Answer Provide Feedback Units ?
To use deformation compatibility equations to calculate loads and deflections for statically indeterminate axially loaded columns. As shown, two composite columns of steel and concrete are used to support a rigid platform. The columns are cylindrical, with a steel bar encased in concrete. The outer diameter of each column is dc = 26 cm . The steel in the left column has a diameter of d1 = 13 cm . A load of P = 56 kN is applied with L1 = 1.8 m and L2 = 1.9 m . The height of the columns is h = 2.2 m . The moduli of elasticity for steel and concrete are Es = 200 GPa and Ec = 30 GPa , respectively.
The wood column is pinned at its base and top. Take E= 10 GPa and or = 15 MPa. (Figure 1) Figure 150 mm" 25 mm 25 mm 75 mm 75 mm 1 of 1 Part A If the eccentric force P = 11.8 kN is applied to the column, determine the maximum normal stress. Express your answer to three significant figures and include the appropriate units. TIGB = Submit Part B Value Request Answer Submit Units If the eccentric force P = 11.8 kN is applied to the column, investigate whether the column is adequate to support this loading without buckling or yielding. ? O The column is adequate to support this loading without buckling or yielding. O The column is inadequate to support this loading without buckling or yielding. Request Answer
Steel bar with dimensions with (10mm and 10mm) subjected to axial load of * 2000N. Determine the stress P 10mm 10mm L=100 mm
Part A The lever is attached to the shaft A using a key that has a width d and length of 26 mm .If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the key is T = 37 MPa (Figure 1) Express your answer with the appropriate units. HA d = Value mm Submit Request Answer Provide Feedback Next > Figure d -20 mm 500 mm 200 N