u= 8+jl1 Ex. 41. Given two complex numbers: v=11+j11. Perform the following arithmetic operations with the complex numbers : u+v=A+jB; in radians. u/v=G+jH; Give the 9 answers in order: A,B,C, D,E,F,G,H,K. Note that the magnitude of u/v (I) is not requested. and u*v=C+jD; u*v=E exp(j F) where F is u/v=I exp(jK) where K is in radians. ans:9

u= 8+jl1 Ex. 41. Given two complex numbers: v=11+j11. Perform the following arithmetic operations with the complex numbers : u+v=A+jB; in radians. u/v=G+jH; Give the 9 answers in order: A,B,C, D,E,F,G,H,K. Note that the magnitude of u/v (I) is not requested. and uv=C+jD; uv=E exp(j F) where F is u/v=I exp(jK) where K is in radians. ans:9

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

what are the complex powers of the elements in the circuit 031811540 03 120 540 03 -jin 0 031811 03181154 1811 03181154 03181150 031811540 081811 620'V (*) 3181153 22 811540 12 03181154 031811540 031811540 01811 3181154 0S 1811
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 10 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is reduced to the half value? 3.536 Vrms . 3.536 Vrms O 5 Vrms . 1.7677 Vrms O 3.536 Vrms. 1.7677 Vrms O 5 Vrms . 5 Vrms ...... O 10 Vrms . 10 Vrms ......
Draw a seven-segment display, show the number highlighted in figure 1 (d3 -d0 are the input, a -g are the outputs). III. Simulation Wavetorm Editor - Cers/Ahmad Fainuz/Desanop/DLD Lab Practice/bedseg - beaeg - bcaseg 2018o03121936sim.vwwt Ee ep Ea w smutation search altera.com Haster Time Bar: ops Pointer: s29 us Start End iterval 529 us o ps 0 ps २ 2.56 us S12 us 75 us 10.24 us 12 s 15.36 us 172 us value at Name Ops do Figure 1
From step1, how did you get that 50+(80*j60/80+j60) = 78.8+j38.4? also in step 2, how did you get that 5/(0.0125-0.0167) = 143.63 + j191.89?
in V1 R2 100k SINE(0 10 100) R1 100k D1 D V2 0 out D D2 V3 0 DC offset[V]: 0 Amplitude[V]: 10 Freq[Hz]: 100 T delay[s]: Theta[1/s]: Phi[deg]: Ncycles: anter 2019-2220 Figure 3-5 Clipper Circuit for LTSPICE Simulation C4. To specify the type of simulation, select "Simulate>>Edit Simulation Cmd" from the menu. Choose "Transient" and enter 30m for Stop time, 0 for Time to start saving data, and 1m for Maximum Timestep. Click OK. C5. Click Run to start the analysis. C6. Place two voltage probes (voltage probes appear when placed on a wire during simulation), one at the input side (at the top of V1) and another at the output side (at the top of D2) of the circuit. What difference do you observe between the input and the output waveforms?
D. Find h22. Express your answer in millisiemens to three significant figures. Enter your answer in rectangular form.
G1 0.01 +0.03 V₁ = 1.040° 0.02 + j0.04 Select one: Ⓒa. 3.095-j0.707 O b. 3.095+j0.707 O c. 2.466-j0.254 O d. 2.234+j0.216 Oe. None of these P3 0.0125 + j0.025 Q3 For the network shown above, with all impedances are marked in pu based on a 100MVA base power, find the actual slack bus real and reactive power, if after seven iterations: V₂=0.9808-j0.0578 & V3-0.9555-j0.0434. 3 P2 Q2
The summation of continuous- time sinusoids is Select one: a. Periodic under certain conditions O b. Always periodic O c. Never periodic O d. Periodic only if all the sinusoids are identical in frequency and phase
C1 L1 R1 V1 Vout V1 contains the fundamental and its harmonics (fo, 2fo, 3fo, ...). The amplitude of the harmonics is inversely proportional to the harmonic number. V(fo) = 10 mV V(2fo) = 10mv/2 = 5 mV V(3fo) = 10mv/3 = 3.33 mV V(4fo) = 10mv/4 = 2.55 mV a) What is the minimum value of Q for the circuit that will attenuate the third harmonic (3fo) in Vout to be less than 1% of the fundamental? b) What is the amplitude of the fifth harmonic (5fo) as a percentage of the fundamental?
Problem: In electronics device laboratory, you need to use the function generator to use different types of signals e.g., sinusoidal wave, square waves, sawtooth waves and so on. Imagine you are planning to make an approximate square wave generator from a sinusoidal wave having peak voltage of [three digits before last digit of your ID] mV to use the produced square wave to study the clamper circuit. You can consider any frequency. You need to avoid using any dc power supply to save the energy. Also consider the amplitude of the produced square wave must be greater than the PIV of the diode. 1. Identify which circuit is necessary for making the generator. Illustrate input-output signals with appropriate labeling. 2. Lift the produced square wave above the x axis by the amount of [your last digit of your ID] V explaining appropriate steps. + Sinusoidal PIV
isn't f=0.88? why is it 0.78 in equation?
R C Vs Vo If there is a unit step function at the input of the circuit above and R=24 and C=1/24, which of the following statements is incorrect for the output waveform? a. There are positive and negative alternans (half regions) in the output wave. b. Its amplitude is "1". c. The output is in triangular waveform. d. There is a 180 degree phase difference between the input and the output. www w e. At t=0 there is a unit impulse (impulse) sign.