Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long vertical tube, for a fluid whose density is 300 kg per cubic meter and viscosity is 1x10 - 4 Pascal-second travelling along a long circular tube of cross sectional area of 1 cm? owing to a pressure gradient of 1,000 Pascal per meter, the average velocity in meter per second (m/s) is Blank 1. **EXPRESS YOUR ANSWER INTO WHOLE SIGNIFICANT FIGURE (NO DECIMAL PLACE)**

Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long vertical tube, for a fluid whose density is 300 kg per cubic meter and viscosity is 1x10 - 4 Pascal-second travelling along a long circular tube of cross sectional area of 1 cm? owing to a pressure gradient of 1,000 Pascal per meter, the average velocity in meter per second (m/s) is Blank 1. EXPRESS YOUR ANSWER INTO WHOLE SIGNIFICANT FIGURE (NO DECIMAL PLACE)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ANSWER ASAP Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long vertical tube, for a fluid whose density is 300 kg per cubic meter and viscosity is 1x10 - 4 Pascal-second travelling along a long circular tube of cross sectional area of 1 cm2 owing to a pressure gradient of 1,000 Pascal per meter, the average velocity in meter per second (m/s) is Blank 1.
Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long vertical tube, for a fluid whose density is 300 kg per cubic meter and viscosity is 1x10 - 4 Pascal-second travelling along a long circular tube of cross sectional area of 1 cm2 owing to a pressure gradient of 1,000 Pascal per meter, the average velocity in meter per second (m/s) is Blank 1.
Water at temperature of 20 °C is flowing inside a straight, smooth pipe with flow rate of 0.05 m3/h . With which pipe diameter will the flow transition from laminar to turbulent? Kinematic viscosity of water at 20 °C is 1.005·10-6 m2/s. Round off the answer to one decimal digit in cm, but enter the answer without the unit.
The glycerin at 40 C flows through a horizontal cylindrical pipe. The length of the pipe is 70 m and the diameter of the pipe is 4 cm. The flow is steady state and fully developed. The velocity of the fluid at the centerline is 6 m/s. PLEASE DRAW THE FIGURE OF THE PIPE and labet the necessary info . The density and the viscosity of the glycerin at 40 0C are 1252 kg/m3 and 0.3073 kg/m.s, respectively. Is this a laminar flow? Write an equation for the variation of the local flow velocity with the radial direction. Determine the shear stress exerted by the glycerin on the wall of the pipe. Calculate the volume flow rate.
Liquid A(sp gr = 0.95) at a temperature of 29°C is flowing at a rate of 120gal/min in a pipe with an inside diameter of 2.343 in. If the reynold number is 5.6 x 10^5. what is the viscosity of liquid A in centipoise. Final answer in four decimal.
The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
COE0051 FLUID MECHANICS 2 PROPERTIES OF FLUIDS Section Break (Continuous)- 1. A 30x60 cm plate is pulled through the oil with viscosity of 0.05 kg/m-s. The distance between the parallel plates are 1.5 cm. If the plate is need to pull at the rate of 0.4 m/s, what is the force needed to attain this velocity? FIXED PLATE лиши 1.5 cm FIXED PLATE October 20, 2022 .5 cm 1.0 cm .4 m/s
The kinematic viscosity of and specific gravity of a liquid are 3.5 x 10-4 m^2 /s and 0.79, respectively. What is the dynamic viscosity of the liquid in N-s/m^2?
Consider the setup shown below, with a valve to adjust the flow of a fluid to an orifice meter equipped with a differential manometer across it, in series with a rotameter that has been previously calibrated for liquid acetone (density= 0.791 g/cm3), the fluid of interest. The rotameter calibration expression was found to be V=1.56R, where the volumetric flow rate is in mL/s and the rotameter reading is unitless. The manometer fluid has a specific gravity of 1.210. a) For one valve setting resulting in a rotameter reading of 82.0 as liquid acetone flows through the system, the height difference of the manometer fluid is 22.0 mm. The volumetric flow rate for this condition in mL/s with 3 sig. fig's is b) For one valve setting resulting in a rotameter reading of 80.0 as liquid acetone flows through the system, the height difference of the manometer fluid is 22.3 mm. The pressure drop for this condition in Pascals (Pa) with 3 sig. fig's is
Ethylene glycol at 60 deg C with a velocity of 4 cm/s enters a 2.5 cm ID tube. At 60 deg C, the viscosity if 4.75 x 10^-6 sq.m/s. Determine the Reynolds number. Choose the correct answer below and PROVIDE A COMPLETE SOLUTION: a. 2000b. 2100c. 200d. 210
An ideal gas at 250 °C and atmospheric pressure flows through a smooth pipe with ID 6-in. The molecular weight of the ideal gas is 35 g/mol, and its viscosity is 0.002 cP. If the average velocity of the gas is 3.5 m/s, determine the pressure drop per unit length (m).
Asap