Foundations of Materials Science and Engineering
6th Edition
ISBN: 9781259696558
Author: SMITH
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 12.15, Problem 91SEP
To determine
Explain why there is a difference in between the tensile strength of the bulk borosilicate glass
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
For a given polymer, the activation energy for the stress relaxation was measured to be 59kj/mol. If the stress relaxation time for this polymer at 7 degree Celsius is 3150 seconds. What is the relaxation time at 110 degree Celsius
Using the aid of a diagram, describe the behaviour stress vs strain of a brittle polymer. Give one example of a brittle pharmaceutical polymer and their function in table formu
A polymer sample of height 700 cm with an area of 6 m2 supports a mass of 70 tons. Youngs modulus of the polymer sample is found to be 60 GPa. Calculate the change in height of the polymer sample, applied stress and strain.
Chapter 12 Solutions
Foundations of Materials Science and Engineering
Ch. 12.15 - Define a composite material with respect to a...Ch. 12.15 - Prob. 2KCPCh. 12.15 - What are some of the advantages of glass...Ch. 12.15 - Prob. 4KCPCh. 12.15 - Prob. 5KCPCh. 12.15 - What properties make carbon fibers important for...Ch. 12.15 - Prob. 7KCPCh. 12.15 - Prob. 8KCPCh. 12.15 - Prob. 9KCPCh. 12.15 - Prob. 10KCP
Ch. 12.15 - Prob. 11KCPCh. 12.15 - Prob. 12KCPCh. 12.15 - Prob. 13KCPCh. 12.15 - Prob. 14KCPCh. 12.15 - Prob. 15KCPCh. 12.15 - Describe the sheet-molding compound manufacturing...Ch. 12.15 - Prob. 17KCPCh. 12.15 - Prob. 18KCPCh. 12.15 - What are the basic raw materials for portland...Ch. 12.15 - What are the names, chemical formulas, and...Ch. 12.15 - List the five main ASTM types of portland cement...Ch. 12.15 - What is asphalt? Where is asphalt obtained?Ch. 12.15 - What are chemical composition ranges for asphalts?Ch. 12.15 - What does an asphalt mix consist of? What is the...Ch. 12.15 - Prob. 25KCPCh. 12.15 - What are the subrings of the annual growth rings...Ch. 12.15 - Prob. 27KCPCh. 12.15 - Prob. 28KCPCh. 12.15 - Prob. 29KCPCh. 12.15 - Prob. 30KCPCh. 12.15 - Prob. 31KCPCh. 12.15 - Prob. 32AAPCh. 12.15 - Prob. 33AAPCh. 12.15 - Prob. 34AAPCh. 12.15 - Prob. 35AAPCh. 12.15 - Prob. 36AAPCh. 12.15 - Prob. 37AAPCh. 12.15 - Prob. 38AAPCh. 12.15 - Prob. 39AAPCh. 12.15 - A unidirectional carbon fiberepoxy resin composite...Ch. 12.15 - Prob. 41AAPCh. 12.15 - Prob. 42AAPCh. 12.15 - Prob. 43AAPCh. 12.15 - Prob. 44AAPCh. 12.15 - Prob. 45AAPCh. 12.15 - If the tensile strength of the Kevlar 49 fibers is...Ch. 12.15 - Prob. 47AAPCh. 12.15 - Prob. 48AAPCh. 12.15 - Prob. 49AAPCh. 12.15 - Prob. 50AAPCh. 12.15 - Prob. 51AAPCh. 12.15 - What types of chemical reactions occur during the...Ch. 12.15 - Prob. 53AAPCh. 12.15 - Which component of portland cement hardens rapidly...Ch. 12.15 - Prob. 55AAPCh. 12.15 - Prob. 56AAPCh. 12.15 - Prob. 57AAPCh. 12.15 - Prob. 58AAPCh. 12.15 - Prob. 59AAPCh. 12.15 - Prob. 60AAPCh. 12.15 - Prob. 61AAPCh. 12.15 - Prob. 62AAPCh. 12.15 - Prob. 63AAPCh. 12.15 - Prob. 64AAPCh. 12.15 - Prob. 65AAPCh. 12.15 - Prob. 66AAPCh. 12.15 - Prob. 67AAPCh. 12.15 - Prob. 68AAPCh. 12.15 - Prob. 69AAPCh. 12.15 - What characteristics are desirable for the...Ch. 12.15 - Prob. 71AAPCh. 12.15 - Prob. 72AAPCh. 12.15 - Prob. 73AAPCh. 12.15 - Prob. 74AAPCh. 12.15 - Prob. 75AAPCh. 12.15 - Prob. 76AAPCh. 12.15 - Prob. 77AAPCh. 12.15 - Why does wood shrink much more in the transverse...Ch. 12.15 - A newly developed metal-matrix composite is made...Ch. 12.15 - Prob. 81AAPCh. 12.15 - Prob. 82AAPCh. 12.15 - Prob. 83AAPCh. 12.15 - Prob. 84AAPCh. 12.15 - Prob. 85AAPCh. 12.15 - Prob. 86AAPCh. 12.15 - Prob. 87SEPCh. 12.15 - Prob. 88SEPCh. 12.15 - Prob. 89SEPCh. 12.15 - Prob. 90SEPCh. 12.15 - Prob. 91SEPCh. 12.15 - Prob. 92SEPCh. 12.15 - (a) In Problem 12.94, if all three beams are to...Ch. 12.15 - Prob. 97SEPCh. 12.15 - Prob. 98SEPCh. 12.15 - Prob. 99SEPCh. 12.15 - Prob. 100SEPCh. 12.15 - Prob. 101SEPCh. 12.15 - Prob. 102SEPCh. 12.15 - Prob. 103SEPCh. 12.15 - Prob. 104SEPCh. 12.15 - In total hip replacement, most surgeons prefer a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The density of an unknown polymer is 1.875 g/cm³ with a % crystallinity of 50%. If the density when totally amorphous is 1.5 g/cm', calculate the density when totally crystalline. Also calculate the density when the % crystallinity is 87%.arrow_forwardFor a given polymer, the activation energy for stress relaxation was measured to be 10 kJ/mol. If the stress relaxation time for this polymer at room temperature is 3,600 s, what would be the relaxation time at 100 ◦C?arrow_forward(a) Draw a qualitative engineering stress-strain curve for A Ductile polymer (i) (ii) A Metal (iii) A ceramic (Iv) (v) A glass A Natural rubber Label carefully. Rationalize your sketch for each materialarrow_forward
- Glass fibres provide longitudinal reinforcement for a nylon material subject to tensile load. The fibre diameter is 20 μm and the volume fraction is 0.45. (Take Young’s modulus of glass fibres as 70 000 MPa and nylon as 2800 MPa)(i)Calculate the Young’s modulus of composite(ii)Determine the tensile strength in the glass fibre if the tensile strength of the composites and matrix is 14 MPa and 11.8 MPa, respectivelyarrow_forwardWhat is Gorilla Glass from Corning? Why does it outperform regular window glass in terms of mechanical properties? Briefly explain utilizing basic mechanical principles. When necessary, provide diagrams to further explain your response.arrow_forwardCalculate the percentage of crystallinity of the following polymer. Density crystallinity is 0.998, density of the amorphous is 0.870 and density of the polymer is 0.925. All densities are in g/cm^3 Answer:arrow_forward
- Nowadays, many cooking utensils are made of polymeric materials. However, people believe that heating plastic utensils would cause harm such as releasing toxic substances. Hence, people are looking for other alternatives to replace plastic. Choose ONE cooking utensil (spatula) and identify the suitable material that will satisfy its criteria. Justify your answer. Your discussion must include the interrelationship between structure-properties-processing of the selected cooking utensil.arrow_forwardA panel of poly(methyl methacrylate) is bolted in the long direction only at 50°C between two other components with zero coefficients of expansion. What is the stress on the polymer at 0°C? Will the polymer break?arrow_forwardA continuous and aligned glass fiber-reinforced composite with modulus of elasticity of 55 GPa. The volume fiber fraction is 40 and the modulus of elasticity of the fiber is 75 GPa. Calculate the volume fraction of epoxy matrix if you know the modulus of elasticity of the modulus of elasticity of the matrix is 2.5 GPa and then determine the strain that is sustained by each phase under applied stress of 27 Mpa. (assume that the cross-section area is 150 mm2)arrow_forward
- A composite material that has boron fibers coated in aluminum has a density of 2.65 g/cm^3. The fibers have a Young's modulus of 380 GPa, and aluminum has a Young's modulus of 70 GPa. The density of the fibers is 2.36 g/cm^3 and the density of the aluminum is 2.70 g/cm^3. What is the volume of the matrix? Answer:arrow_forwardCalculate the typical relaxation time for silicate glassand comment on its propensity for stress relaxation at roomtemperature. E ~ 70 GPa and η ~ 1 x 1012 GPa-s (1022poise).arrow_forwardExplain what the following terms mean:decomposition temperature, heat distortion temperature, glass-transition temperature, and melting temperature. Why is itthat thermoplastics do not have a fixedmelting or glass-transition temperature?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
composite-materials; Author: Tonya Coffey;https://www.youtube.com/watch?v=Vu6ik-bcKf4;License: Standard youtube license