The first Leyden jar was probably discovered by a German clerk named E. Georg von Kleist. Because von Kleist was not a scientist and did not keep good records, the credit for the discovery of the Leyden jar usually goes to physicist Pieter Musschenbroek from Leyden, Holland. Musschenbroek accidentally discovered the Leyden jar when he tried to charge a jar of water and shocked himself by touching the wire on the inside of the jar while holding the jar on the outside. He said that the shock was no ordinary shock and his body shook violently as though he had been hit by lightning. The energy from the jar that passed through his body was probably around 1 J, and his jar probably had a capacitance of about 1 nF.
- a. Estimate the charge that passed through Musschenbroek’s body.
- b. What was the potential difference between the inside and outside of the Leyden jar before Musschenbroek discharged it?
Want to see the full answer?
Check out a sample textbook solutionChapter 27 Solutions
Physics for Scientists and Engineers: Foundations and Connections
- What is a characteristic that is common to a steel sheet, copper wire. metal paper clip and a wooden spoon does not have? * O all are conductors and allow electrons to flow except for the wooden spoon O all are insulators and allow protons to flow except the wooden spoon O all are insulators and allow electrons to flow except for the wooden spoon O all are conductors and allow protons to flow except for the wooden spoon.arrow_forwardAsaparrow_forwardThe following are electron carriers in a hypothetical biological system: Electron Carriers (E° , V) A (0.17 V), B (0.04 V), C (0.31 V), D (-0.65 V), E (-0.25 V). a. Which electron carrier will be the best electron donor? b. Which electron carrier will be the final electron acceptor?arrow_forward
- Electrons flow through a 3.0-mm-diameter aluminum wire at 1.8×10−4 m/s. How many electrons move through a cross section of the wire each day?arrow_forwardThe circuit shown in the diagram contains a battery and two wires made of the same material, but with different diameters. Each wire is 10 cm long, has 7 x 1027 mobile electrons per cubic meter, and an electron mobility of 5 x 10-5 (m/s)/(V/m). The diameter of wire 1 is 3 mm, and the diameter of wire 2 is 0.8 mm. Location A is inside wire 1, and location B is inside wire 2. A steady state current flows through the circuit. Show Transcribed Text B wire 1 wire 2 What is average drift speed of electrons at location B, inside wire 2? VB = m/sarrow_forward008 A length of metal wire has a radius of 0.004 m and a resistance of 0.11 2. When the potential difference across the wire is 17 V, the electron drift speed is found to be 0.000353 m/s. Based on these data, calculate the density of free electron in the wire. The fundamental charge is 1.6 × 10 Answer in units of m ¬19 C.arrow_forward
- 1 %VY lI. A 9:1. د المرحلة الأولی B.docx الجامعة المستنصرية كلية العلوم / قسم الفيزياء المرحلة الأولي B Q6:Two equal positive charges q.= q.=2x10 C interact with a third charge q-4x10°C. Find the magnitude and direction of the resultant force on q.. 30cm 40cm Q2:Find the electric field at point p as shown in the figure if q. = 2µC, q = -8µC and q = 12µC. 50cm 12C S0cm S0cm ...arrow_forwardThe voltage across a membrane forming a cell wall is 84 mV and the membrane is 7.5 nm thick. What is the electric field strength in the cell wall, in volts per meter?arrow_forwardHow many electrons have to be moved by a car battery containing 7.20×105 J at 12 V to reduce the energy by 1%?arrow_forward
- A constant current transfers 10*10^14 electrons onto one plate of a capacitor in 3 minutes [min]. (a) What is the current, in units of amperes [A]? Express the answer using an appropriate SI prefix such that there are only 1, 2, or 3 digits shown to the left of the decimal. (b) If the capacitor has a capacitance of microfarads [F], what is the voltage in units of volts [V] across the capacitor?arrow_forwardAn insulating belt moves at speed 30 m/s and has a width of 50 cm. It carries charge into an experimental device at a rate corresponding to 100 mA.What is the surface charge density on the belt?arrow_forwardSome types of spiders build webs that consist of threads made of dry silk coated with a solution of a variety of compounds. This coating leaves the threads, which are used to capture prey, hygroscopic—that is, they attract water from the atmosphere. It has been hypothesized that this aqueous coating makes the threads good electrical conductors. To test the electrical properties of coated thread, researchers placed a 5-mm length of thread between two electrical contacts. The researchers stretched the thread in 1-mm increments to more than twice its original length, and then allowed it to return to its original length, again in 1-mm increments. Some of the resistance measurements are shown in the table: (a) What is the best explanation for the behavior exhibited in the data? (b) If the conductivity of the thread results from the aqueous coating only, how does the cross-sectional area of the coating compare when the thread is 13 mm long versus the starting length of 5 mm? Assume that the…arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning