Statics and Mechanics of Materials
2nd Edition
ISBN: 9780073398167
Author: Ferdinand P. Beer, E. Russell Johnston Jr., John T. DeWolf, David Mazurek
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 4, Problem 104RP
To determine
(a)
The distance
To determine
(b)
The tension in the string attached to the ring.
To determine
(c)
The reaction force at point C.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A thin ring of mass 2 kg and radius r=140 mm is held against a frictionless wall by a 125-mm string AB. Determine (a) the distance d, (b) the tension in the string, (c) the reaction at C.
A thin ring with a mass of 2 kg and radius r = 140 mm is held against a frictionless wall by a 125-mm string AB . Determine (a) the distance d, (b) the tension in the string, (c) the reaction at C.
2. A 200-mm lever and a 240-mm pulley are welded to the axel BE that is supported by bearings
at C and D. Assume that the bearing at D does not exert any axial thrust. A 720-N vertical force
is applied at A when the lever is horizontal. Determine (a) the tension, T, in the cord, and (b) the
reactions at C and D.
Ans: T = 1200N, C = 400î +1200 N,
D=-1600î – 480ĵ N
%3D
40 mm
80 mm
120 mm
200 mm
D
E
120 mm
720 N
Chapter 4 Solutions
Statics and Mechanics of Materials
Ch. 4.1 - For the beam and loading shown, determine (a) the...Ch. 4.1 - A 3200-lb forklift truck is used to lift a 1700-lb...Ch. 4.1 - A gardener uses a wheelbarrow to transport a 250-N...Ch. 4.1 - A load of lumber of weight W=25 kN is being raised...Ch. 4.1 - Three loads are applied as shown to a light beam...Ch. 4.1 - Three loads are applied as shown to a light beam...Ch. 4.1 - For the beam and loading shown, determine the...Ch. 4.1 - Prob. 8PCh. 4.1 - Prob. 9PCh. 4.1 - The lever BCD is hinged at C and attached to a...
Ch. 4.1 - The lever BCD is hinged at C and attached to a...Ch. 4.1 - A lever AB is hinged at C and attached to a...Ch. 4.1 - Determine the reactions at A and B when...Ch. 4.1 - Prob. 14PCh. 4.1 - Prob. 15PCh. 4.1 - Prob. 16PCh. 4.1 - A light bar AD is suspended from a cable BE and...Ch. 4.1 - Prob. 18PCh. 4.1 - Prob. 19PCh. 4.1 - Two slots have been cut in plate DEF, and the...Ch. 4.1 - A 6-m telephone pole weighing 1600 N is used to...Ch. 4.1 - Prob. 22PCh. 4.1 - For the and crate of Prob. 4.22 and assuming that...Ch. 4.1 - A tension of 20 N is maintained in a tape as it...Ch. 4.1 - The bracket ABC can be supported in the eight...Ch. 4.1 - Eight identical 500750-mm rectangular plates, each...Ch. 4.2 - Determine the reactions at B and C when a=30mm.Ch. 4.2 - Prob. 28PCh. 4.2 - A 12-ft wooden beam weighing 80 lb is supported by...Ch. 4.2 - Prob. 30PCh. 4.2 - One end of rod AB rests in the comer A and the...Ch. 4.2 - Using the method of Sec. 4.2B, solve Prob. 4.12.Ch. 4.2 - Prob. 33PCh. 4.2 - A 40-lb roller of 8-in. diameter, which is to be...Ch. 4.2 - Member ABC is supported by a pin and bracket at B...Ch. 4.2 - Prob. 36PCh. 4.2 - Prob. 37PCh. 4.2 - For the frame and loading shown, detennine the...Ch. 4.2 - For the boom and loading shown, determine (a) the...Ch. 4.2 - A slender rod BC of length L and weight W is held...Ch. 4.2 - Prob. 41PCh. 4.2 - Prob. 42PCh. 4.2 - Prob. 43PCh. 4.2 - Prob. 44PCh. 4.2 - Solve Prob. 4.44, assuming that the 170-N force...Ch. 4.2 - Prob. 46PCh. 4.2 - Prob. 47PCh. 4.2 - Prob. 48PCh. 4.2 - Prob. 49PCh. 4.2 - Prob. 50PCh. 4.3 - Two transmission belts pass over a double-sheaved...Ch. 4.3 - Solve Prob. 4.51, assuming that the pulley rotates...Ch. 4.3 - A 48-ft sheet of plywood weighing 40 lb has been...Ch. 4.3 - Prob. 54PCh. 4.3 - Prob. 55PCh. 4.3 - Prob. 56PCh. 4.3 - Prob. 57PCh. 4.3 - Prob. 58PCh. 4.3 - Prob. 59PCh. 4.3 - Prob. 60PCh. 4.3 - A 48-in. boom is held by a ball-and-socket joint...Ch. 4.3 - Prob. 62PCh. 4.3 - The 6-m pole ABC is acted upon by a 455-N force as...Ch. 4.3 - A 600-lb crate hangs from a cable that passes over...Ch. 4.3 - The horizontal platform ABCD weighs 60 lb and...Ch. 4.3 - Prob. 66PCh. 4.3 - Prob. 67PCh. 4.3 - Prob. 68PCh. 4.3 - A 10-kg storm window measuring 9001500 mm is held...Ch. 4.3 - Prob. 70PCh. 4.3 - Prob. 71PCh. 4.3 - Solve Prob. 4.69, assuming that the hinge at A has...Ch. 4.3 - Prob. 73PCh. 4.3 - Three rods are welded together to form a corner...Ch. 4.4 - Determine whether the block shown is in...Ch. 4.4 - Prob. 76PCh. 4.4 - Determine whether the block shown is in...Ch. 4.4 - Prob. 78PCh. 4.4 - Prob. 79PCh. 4.4 - Prob. 80PCh. 4.4 - Prob. 81PCh. 4.4 - Prob. 82PCh. 4.4 - Prob. 83PCh. 4.4 - Knowing that P=100N, determine the range of values...Ch. 4.4 - A 120-lb cabinet is mounted on casters that can be...Ch. 4.4 - Prob. 86PCh. 4.4 - A 40-kg packing crate must be moved to the left...Ch. 4.4 - A 40-kg packing crate is pulled by a rope as...Ch. 4.4 - Prob. 89PCh. 4.4 - Prob. 90PCh. 4.4 - Prob. 91PCh. 4.4 - Prob. 92PCh. 4.4 - Prob. 93PCh. 4.4 - Prob. 94PCh. 4.4 - Prob. 95PCh. 4.4 - Prob. 96PCh. 4.4 - The cylinder shown is of weight W and radius r,...Ch. 4.4 - Prob. 98PCh. 4 - A T-shaped bracket supports the four loads shown....Ch. 4 - Neglecting friction and the radius of the pulley,...Ch. 4 - Member ABC is supported by a pin and bracket at B...Ch. 4 - Prob. 102RPCh. 4 - Prob. 103RPCh. 4 - Prob. 104RPCh. 4 - Prob. 105RPCh. 4 - Prob. 106RPCh. 4 - Prob. 107RPCh. 4 - Prob. 108RPCh. 4 - Prob. 109RPCh. 4 - Two 10-lb blocks A and B are connected by a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Solution for A weight W = 500 KN rests on the weightless and friction less bar AB. The cable connecting W and point B passes over a frictionless pulleys. Find the Reaction (Ra) at point A.arrow_forwardA 12-ft wooden beam weighing 80 lb is supported by a pin and bracket at A and by cable BC. Find the reaction at A and the tension in the cable.arrow_forwardTwo transmission belts pass over pulleys welded to a shaftwhich is supported by bearings at B and D. If the pulley at A has a radius of 2.5 in., and the pulley at C has a radius of 2 in. and it is known that the system rotates with a constant angular velocity, determine a) the tension T, b) the reactions at B and D. Suppose that the bearing at D does not exert any axial thrust force and does not take into account the weights of pulleys and shaftarrow_forward
- The mechanism shown consists of a crank (bar AB), a connecting rod (bar BC) and the piston C that slides on the smooth surface (without friction) The combustion of gasoline produces a force P on the piston and this is maintained in equilibrium with moment M applied at A. The length of the crank is 78 mm, of the connecting rod is 279 mm, the moment is 84 nm, and the angle theta is 0.41 radians. Determine the value of P in Newtons P B Marrow_forward4.46 The 90-kg man, whose center of gravity is at G, is climbing a uniform ladder. The length of the ladder is 5 m, and its mass is 20 kg. Friction may be neglected. (a) Compute the magnitudes of the reactions at A and B for x = 1.5 m. (b) Find the distance x for which the ladder will be ready to fall. =5 m 1.2 m -1.6 m --| Fig. P4.46arrow_forwardEQULIBRIUM OF RIGID BODIES - 3D The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 251 N and if a = 3m, determine the magnitude of the reaction (N) at A along the z-axis. Round off only on the final answer expressed in 3 decimal places.arrow_forward
- A 5 x 8-ft sign of uniform density weighs 270 lb and is supported by a ball-and-socket joint at A and by two cables. Determine the tension in each cable and the reaction at A.arrow_forwardA 260-kg uniform rectangular plate is supported in the position shown in the figure by hinges A and B and by a cable DCE that passes over a frictionless hook at C. Assume that the tension is the same in both parts of the cable and that hinge B does not exert any axial thrust. 450 mm 90 mm 690 mm A The reaction at A is ( The reaction at Bis 960 mm C 270 mm 90 mm B E 675 mm Determine the reactions at A and B. Round the final answer to one decimal place. N) i+ N) k. N)j + N)j + N) k. xarrow_forwardPractice Problem 4.4.8: The 90-kg man, whose center of gravity is at G, is climbing a uniform ladder. The length of the ladder is 5 m, and its mass is 20 kg. Friction may be neglected. (a) Compute the magnitudes of the reactions at A and B for x = 1.5m.(b) Find the distance x for which the ladder will be ready to fall. G L=5 m 1.2 m -1.6 m–|arrow_forward
- The spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless surface rests agains the shaft at B. If a 300-N force P is exerted on the spanner at D, find (a) the reaction at B, (b) the component of the reaction at A in a direction perpendicular to AC. 50° D B 75 mm -375 mmarrow_forwardThe uniform (18 kg) bar OA is held in the position Shown by the pin at o" and the cable AB. Detemine the tension T in the cable and the magnitude of the reactions at pin o". 1.5 m 60° 1.2 marrow_forwardThe given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively, as shown. A model of the truss was made in a laboratory, and it was found out that the values of internal forces in members A- L, A-B, and B-K are as indicated in the table. If the vertical reactions at A and G are 6.667 KN and 5.333 KN respectively, complete the table and answer the succeeding questions. Approximate all answers up to three decimal places. What is the behavior of the internal reaction of Member A-L?" 8 kN 4 kN D E F 3 m L K J 12 m, 6 @ 2 m Member Experimental 13.533 14.680 Computational Percent Error A-L A-B B-K 0.012 O compression O none of the choices O tensionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY