Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.13P
The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider steady viscous flow through a small horizontal tube. For this type of flow, the pressure gradient along the tube, Δp ⁄ ΔL should be a function of the viscosity Y, the mean velocity V, and the diameter D. By dimensional analysis, derive a func- tional relationship relating these variables.
Fluid mechanics
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN
When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow andthen undergoes transition to turbulence at a time ttr which depends upon the pipe diameter D,fluid acceleration a, density ρ, and viscosity µ. Arrange this into a dimensionless relationbetween ttr and D.
Chapter 5 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 5 - Evaluate the Reynolds number for flow over a tube...Ch. 5 - 5.2 Evaluate the Prandtl number from the following...Ch. 5 - Evaluate the Nusselt number for flow over a sphere...Ch. 5 - 5.4 Evaluate the Stanton number for flow over a...Ch. 5 - Evaluate the dimensionless groups hcD/k,UD/, and...Ch. 5 - 5.6 A fluid flows at 5 over a wide, flat plate 15...Ch. 5 - 5.7 The average Reynolds number for air passing in...Ch. 5 - Prob. 5.8PCh. 5 - When a sphere falls freely through a homogeneous...Ch. 5 - 5.10 Experiments have been performed on the...
Ch. 5 - 5.13 The torque due to the frictional resistance...Ch. 5 - The drag on an airplane wing in flight is known to...Ch. 5 - 5.19 Suppose that the graph below shows measured...Ch. 5 - Engine oil at 100C flows over and parallel to a...Ch. 5 - For flow over a slightly curved isothermal...Ch. 5 - Air at 20C flows at 1 m/s between two parallel...Ch. 5 - Air at 1000C flows at an inlet velocity of 2 m/s...Ch. 5 -
5.43 A refrigeration truck is traveling at 130...Ch. 5 - The air-conditioning system in a Chevrolet van for...Ch. 5 - Determine the rate of heat loss from the wall of a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The thrust force, F generated by a propeller is found to depend on the followingparameters: diameter D, forward velocity u, density ρ, viscosity µ and rotationalspeed N. Determine the dimensionless parameters to correlate the phenomenonarrow_forwardThe power P required to drive a propeller is known to depend on the diameter of the propeller D, the density of fluid ρ, the speed of sound a, the angular velocity of the propeller ω, the freestream velocity V , and the viscosity of the fluid µ. (a) How many dimensionless groups characterize this problem? (b) If the effects of viscosity are neglected, and if the speed of sound is not an important variable, express the relationship between power and the other variables in nondimensional form. (c) A one-half scale model of a propeller is built, and it uses Pm horsepower when running at a speed ωm. If the full-scale propeller in the same fluid runs at ωm/2, what is its power consumption in terms of Pm if the functional dependence found in part (b) holds? What freestream velocity should be used for the model test?arrow_forwardWhen fluid in a pipe is accelerated linearly from rest, it begins as laminar flow andthen undergoes transition to turbulence at a time ttr which depends upon the pipe diameter D,fluid acceleration a, density ρ, and viscosity µ. Arrange this into a dimensionless relationbetween ttr and D. (Fluid Mechanics)arrow_forward
- A- Womersley number (a) of a human aorta is 20 and for the rabbit aorta is 17, the blood density is approximately the same across the species. The values of viscosity were 0.0035 Ns/m² for the human and 0.0040 Ns/m² for the rabbit. The diameter of the aorta is 2.0 cm for the man, and 0.7 cm for the rabbit, estimate the heart rate beats per minute (bpm) for both speciesarrow_forwardA liquid of density ? and viscosity ? flows by gravity through a hole of diameter d in the bottom of a tank of diameter DFig. . At the start of the experiment, the liquid surface is at height h above the bottom of the tank, as sketched. The liquid exits the tank as a jet with average velocity V straight down as also sketched. Using dimensional analysis, generate a dimensionless relationship for V as a function of the other parameters in the problem. Identify any established nondimensional parameters that appear in your result. (Hint: There are three length scales in this problem. For consistency, choose h as your length scale.) except for a different dependent parameter, namely, the time required to empty the tank tempty. Generate a dimensionless relationship for tempty as a function of the following independent parameters: hole diameter d, tank diameter D, density ? , viscosity ? , initial liquid surface height h, and gravitational acceleration g.arrow_forwardConsider a Falling Sphere Viscometer, which is used to measure the viscosity μ of a fluid by observing the terminal velocity of a heavy sphere (density Ps and diameter D) falling under gravity in a column of the fluid (density pf). (a) Use Dimensional Analysis to derive a formula for the drag force exerted on the sphere by the viscous fluid when it is moving at speed v through the fluid. (b) How is the terminal velocity of the sphere related to the fluid viscosity? (c) If the sphere starts from rest, use Dimensional Analysis to predict the timescale over which the sphere will reach its terminal velocity. Please use dimensiona analysis to solve the problem Answr for part a= Fd=KmuVD answer for part b=V=Fd/kmuD Please solve only for part C (part a and b no need to solve)and expalin in detail Thanksarrow_forward
- By dimensional analysis, obtain an expression for the drag force (F) on a partially submerged body moving with a relative velocity (u) in a fluid; the other variables being the linear dimension (L), surface roughness (e), fluid density (p), and gravitational acceleration (g).arrow_forwardTaylor number (Ta) is used here to describe the ratio between the inertia effect and the viscous effect. By applying Buckingham Pi's Theorem, determine an equation for Ta as a function of the radius of inner cylinder (r), cylinder tangential velocity (v), fluid dynamic viscosity (u), gap distance (L) and fluid density (p). Q4arrow_forwardWe want to predict the drag force on a remote-control airplane as it flies through air having a density of 1.21 kg/m³ and a viscosity of 1.76x10- Pa-s. The airplane's fuselage has a diameter of 200 mm and the airplane will fly through air at a speed of 32 m/s. A model of the airplane's fuselage will be tested in a pressurized wind tunnel. The diameter of the model is 75 mm and the density and viscosity of the air in the wind tunnel are 3.00 kg/m³ and 1.82× 10-5 Pa-s, respectively. a) The diameter of the airplane's fuselage will be used to define the Reynolds number Re, for the flow around the fuselage. Compute the Reynolds number for the flow around the airplane's fuselage (answer: Re, = 4.40x 10'). b) Find the speed of the air that should be used to test a model of the fuselage in the wind tunnel to correctly model dynamic conditions (answer: 35.6 m/s). c) The model is tested in the wind tunnel at four speeds that bracket the speed computed above. The measured drag forces on the…arrow_forward
- 1ODiem # The side thrust F, for a smooth spinning ball in a fluid is a function of the ball diameter D, the free-stream velocity V, the densityp, the viscosityu, and the angular velocity of spino. F= f( D, ρ, μ, V, ω) Using the Buckingham Pi theorem to express this relation in dimensionless form. Farrow_forwardIn falling ball viscometer experiment, the viscometer with a calibration factor K=0.3 is used to measure the viscosity of oil with density p3D 0.8 gr/cm and the density of Tantalum ball is 16.6 gr/cm, if the ball is observed to fall 250 mm in time 50.3 sec. What is the viscosity of the oil (in cp)?arrow_forwardThe time t d to drain a liquid from a hole in the bottom of atank is a function of the hole diameter d , the initial fluidvolume y 0 , the initial liquid depth h 0 , and the density ρ andviscosity μ of the fluid. Rewrite this relation as a dimensionlessfunction, using Ipsen’s method.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY