Water at 50°C flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long in the flow direction and its surface is maintained at a uniform temperature of 10.0°C. Calculate the steady rate of heat transfer per unit width of the plate. Remember the flow over the plate is laminar when Re < 5x 105.

Water at 50°C flows over a large plate at a velocity of 30.0 cm/s. The plate is 1.0 m long in the flow direction and its surface is maintained at a uniform temperature of 10.0°C. Calculate the steady rate of heat transfer per unit width of the plate. Remember the flow over the plate is laminar when Re < 5x 105.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.57P

See similar textbooks

Similar questions

A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
A flat plate of width 1 m and length 0.2 m is maintained at a temperature of 32 °C. Water at 22 °C flows across the top of the plate in parallel flow (see diagram below). Determine (a) the average convection heat transfer coefficient, and (b) the convection heat transfer rate from the top of the plate when water has a flow rate of 0.5 m/s. Assume steady-state, and find water properties in the "Given information page". Water w = 1 m L= 0.2 m
-1/5 A// For laminar flow over a flat plate, the local heat transfer coefficient h, is known to vary as x¹/5, where x is the distance from the leading edge (x =0) of the plate. What is the ratio of the average coefficient between the leading edge and some location x on the plate to the local coefficient at x? for velocity equation u= 2-0.43x+x² Plot the local heat transfer coefficient over a 0.8 cm length(take T-35c) B// Air at 1 atm and 15°C flows through a long rectangular duct 7.5 cm by 15 cm. A 1.8-m section of the duct is maintained at 120°C, and the average air temperature at exit from this section is 65°C. Calculate the airflow rate and the total heat transfer
A long and wide heated plate is maintained at uniform temperature. You have to calculate the flux from the plate if a fluid is flowing over the plate at 1 m/s. The length of the plate in the direction of the flow is 10 m. The fluid is air. Temperature of the plate is 60°C and temperature of average heat 81-3 u 10°C.
Topic: Heat transfer Completely solve and box the final answer. 1. A 20degC water flows to 50cmx60cm flat plate with velocity of 5.2m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent?
Water at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s. The plate surface temperature is uniform at 86oC. Calculate: a) Thermal boundary layer thickness at x = 8 cm from leading edge; b) Local heat flux on x = 8 cm from leading edge; c) Total heat transfer rate in the area of plate L = 8 cm from the leading edge and width w = 10 cm.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Air at 20 C is flowing over a flat plate ( 6m long and 1.5m wide). The plate is maintained at 140 C. Find the heat loss from the plate if the air is flowing parallel to 6m side with a velocity of 2 m/s. What is the percentage change in heat transfer if the air flow is parallel to 1.5m side. The properties of air are: p=1.06 kg/m v 2.548x10 m/s, k=0.0295 W/mK and Pr-0.7. Nu =0.664Res Pr1 for laminar flow Nu, = (0.037RE-871)Pr for turbulent flow
Given engine oil at 60 oC flows over the upper surface of a 5 m long flat plate which temperature is 20 oC. Justify the value of x (m2/s) to get the turbulent flow for the total drag force and the rate of heat transfer per unit width of the plate. Discuss your idea.
For laminar flow over a flat plate, the local heat transfer coefficient hx = x-1/2 where x is the distance from the leading edge (x=0) of the plate. What is the average heat transfer coefficient hx from the leading edge to location x.
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?