Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12, Problem 12.25P
Calculate the maximum shear stress developed in a
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
A solid steel shaft is to transmit 120hp. The allowable shear stress is 8,000 psi. Calculate the diameter if the shaft speed is 3000 rpm.
Design a hollow circular steel shaft to transmit an applied torque of 360,000 in-lbs. Theallowable shear stress is 6,000 psi and the inside diameter is to be 0.6 times the outsidediameter.
Chapter 12 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 12 - Determine the internal resisting torque in the...Ch. 12 - Determine the internal resisting torque in the...Ch. 12 - Calculate the maximum shear stress developed in a...Ch. 12 - Calculate the allowable torque for a hollow steel...Ch. 12 - Calculate the allowable torque that may be applied...Ch. 12 - A hollow circular steel shaft has a 100-mm outside...Ch. 12 - Design a solid circular steel shaft to transmit an...Ch. 12 - Calculate the shear stresses at the outer and...Ch. 12 - A hollow shaft is produced by boring a...Ch. 12 - Pulleys C and D are attached to shaft AB, as...
Ch. 12 - Calculate the angle of twist a 3-in-diameter...Ch. 12 - Calculate the angle of twist a 65-mm-diameter...Ch. 12 - Calculate the angle of twist a 4-in.-diameter...Ch. 12 - Prob. 12.14PCh. 12 - Prob. 12.15PCh. 12 - A solid steel shaft is to resist a torque of 9000...Ch. 12 - A hollow steel shaft has a 50-mm outside diameter...Ch. 12 - If the shaft of Problem 12.17 were solid, with the...Ch. 12 - An automobile engine develops 90 hp at 3500 rpm....Ch. 12 - Calculate the speed (rpm) at which a...Ch. 12 - Select the diameter of a solid circular steel...Ch. 12 - Select the diameter for a hollow steel shaft that...Ch. 12 - A 6-ft-long solid steel shaft with a diameter of 4...Ch. 12 - The outside and inside diameters of a hollow steel...Ch. 12 - Calculate the maximum shear stress developed in a...Ch. 12 - Write a program that will calculate the allowable...Ch. 12 - Write a program that will generate a table of...Ch. 12 - Rework the program of Problem 12.27 using SI...Ch. 12 - Write a program that will generate a table of...Ch. 12 - Compute the maximum shear stress in the hollow...Ch. 12 - Calculate the allowable torque that may be applied...Ch. 12 - Design a hollow steel shaft to transmit a torque...Ch. 12 - A 32-in.-long solid steel circular shaft, 3 in. in...Ch. 12 - The 65-mm-diameter solid shaft shown is subjected...Ch. 12 - Rework Problem 12.34, changing the diameter of...Ch. 12 - Compute the maximum shear stress in the circular...Ch. 12 - Determine the allowable torque a hollow steel...Ch. 12 - A 1.00-m-long steel wire, 4 mm in diameter, is...Ch. 12 - Select the outside and inside diameters for a...Ch. 12 - A solid aluminum shaft, 6 ft in length, is to...Ch. 12 - A 25-mm-diameter solid shaft with an allowable...Ch. 12 - Compute a. the maximum shear stress developed in a...Ch. 12 - What horsepower can a solid steel shaft 6 in. in...Ch. 12 - Calculate the maximum power that may be...Ch. 12 - A small ski lift has a main cable driving wheel 11...Ch. 12 - A 32-mm-diameter solid shaft transmits 100 kW of...Ch. 12 - A solid steel shaft is to transmit power of 58 kW...Ch. 12 - Select the diameter for a solid steel shaft that...Ch. 12 - A solid steel shaft is to transmit 100 hp at a...Ch. 12 - Two shafts-one a hollow steel shaft with an...Ch. 12 - A 112 -in.-diameter solid steel shaft is 40 ft in...Ch. 12 - A solid steel shaft is to transmit 120 hp. The...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A steel shaft is to be manufactured either as a solid circular solid bar or as a circular tube. The shaft is required to transmit a torque of 1200N-m without exceeding an allowable shear stress of 40MPa or an allowable rate twist of 0.75deg/m. The shear modulus of steel is 78GPa. Compute the required diameter of the solid shaft & compute the required outer diameter of the hollow shaft if its thickness is 1/10 of its outer diameter.arrow_forwardCompute the torsional shear stress that would be produced in a solid circular shaft having a diameter of 20 mm whe subjected to a torque of 280 N m.arrow_forwardCompute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to a torque of 800N-m.arrow_forward
- Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.arrow_forwardCalculate the maximum allowable torque (in-lbs). A solid steel shaft is made from AISI 1045 steel, with a 9.0" diameter and length of 44". The maximum allowable shear stress on the material is 6200 psi. Based on the answer above, what is the required RPM if this shaft needs to transmit 4500 HP at the maximum allowable torque?arrow_forwardCalculate the maximum torsional shear stress that would develop in a solid circular shaft, having a diameter of 32 mm, if it is transmitting 95 kW while rotating at 525 rpm. (●_^) hope for your help sooonest!arrow_forward
- An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power 1. а. allowing a stress of 50 MPa and assuming the shaft to be solid. b. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power allowing a stress of 50 MPa and assuming the hollow with a bore equal to half the outside diameter. For Solid Shaft:T: = D't For Hollow Shaft:T= 16 16D Tm = P/warrow_forwardDesign a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.arrow_forwardA hollow shaft must transmit 1400 kW at 180 rpm. The outside diameter must be 1.6 times the inside diameter. The maximum torque is 30% more than the mean torque. Calculate: 1. The diameters of the hollow shaft if the allowable stress is 200 MPa. 2. The diameter of the solid shaft if the allowable stress is 200 MPa.arrow_forward
- A hollow shaft for a rotary compressor is to be designed to transmit a maximum of torque of 4750 N-m. The shear stress in shaft, if the ratio of the inside to the outside diameter is 0.4arrow_forwardA shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.arrow_forward• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft • Briefly describe which type of shaft is more effective. • See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Everything About COMBINED LOADING in 10 Minutes! Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=N-PlI900hSg;License: Standard youtube license