Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 55, Problem 6ASRQ
Technician A feels up and down the face or along the return bends of the condenser for a temperature change and says that there should be a gradual change from hot to warm from the bottom to the top. Technician B says that a restriction in the condenser will be evident by a sudden change in temperature. Who is correct?
- Technician A only
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Which of the following statements is false?
The condenser is normally mounted just in front of the radiator.
The receiver/dryer is a storage tank for the liquid refrigerant from the condenser.
An accumulator is not used in any system with a receiver/dryer.
All of the above.
Technician A says that suction lines become very warm during A/C operation. Technician B says that discharge lines connect the compressor to the condenser. Who is correct?
What is fan static pressure?
Chapter 55 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 55 - What should you do if you suspect that an...Ch. 55 - Explain how dye can be used to find leaks in the...Ch. 55 - What is the purpose of the thermostatic switch in...Ch. 55 - Why should the probe of an electronic leak...Ch. 55 - How will air trapped in the A7C system affect...Ch. 55 - Which of the following statements best defines the...Ch. 55 - Which of the following statements is not true...Ch. 55 - To charge an air-conditioning system while it is...Ch. 55 - All of the following are true statements about...Ch. 55 - A very important part of a performance test on an...
Ch. 55 - While conducting a pressure test on an A/C system,...Ch. 55 - The high-side pressure on a system with a cycling...Ch. 55 - When checking an A/C system, the evaporators inlet...Ch. 55 - All of these are good reasons for replacing an...Ch. 55 - In an AZC system, if the low-side pressure is...Ch. 55 - Technician A says that evacuating (pumping down)...Ch. 55 - Technician A says that some refrigerant leaks can...Ch. 55 - Technician A says that the presence of oil around...Ch. 55 - Technician A says that a faulty accumulator will...Ch. 55 - Technician A says that air in the system can cause...Ch. 55 - Technician A feels up and down the face or along...Ch. 55 - Technician A says that a manifold gauge set can be...Ch. 55 - While discussing an inoperative blend air door:...Ch. 55 - Two technicians were discussing how comparing the...Ch. 55 - While conducting an A/C system performance test:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that when the refrigerant is pumped out of the compressor and sent to the condenser, heat in the refrigerant is moved to the outside air by conduction and convection. Technician B says that the refrigerant leaves the bottom of the condenser as a high-pressure, high-temperature liquid. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTechnician A says that air in the system can cause excessive pressure within the system, restricting the refrigerants ability to change its state from gas to liquid within the refrigeration cycle. Technician B says that moisture can cause freeze-up at the cap tube or expansion valve, which restricts refrigerant flow or blocks it completely. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTechnician A says that some refrigerant leaks can also be traced to pinholes in the evaporator caused by acid, which forms when water and refrigerant mix. Technician B says that leaks are most often found at the compressor hose connections and at the various fittings and joints in the system. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- Technician A says that when the A7C system is off, the refrigerant occupies the system as a liquid and its pressure is the same throughout the system. Technician B says that refrigerant is pumped out of the compressor as a high-pressure, high-temperature vapor and is sent to the condenser. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhy should a condenser be covered with a sheet before leak checking it with an electronic detector?arrow_forwardWhen condenser tubes become fouled, they may be cleaned by A. using a steel brush. B. using a brass brush. C. using a chisel and hammer. D. running a mixture of sand and water through them.arrow_forward
- If a condenser circuit breaker is tripped, you should A. reset it. B. check the suction pressure. C. check the high-side pressure. D. perform a resistance check of the compressor section.arrow_forwardWhat is the purpose of a pressure regulator?arrow_forwardWhat is the mean effective pressurearrow_forward
- Choose the correct answer The suction pressure of a refrigerant should be as low as possible The suction pressure of a refrigerant should be as high as possible The suction pressure of a refrigerant should be as constant as possible None of the above Oarrow_forwardWhich of the following statements is not true? A direct acting PRV: Is complex in construction, therefore can malfunction if a very small dirt gets trapped inside the valve, which may result in safety hazard Offers uneven flow Does not provide precise pressure control Causes more wastage of HP compared to a compound one Which of the following basic system components has the primary function of removing the heat of compression from the air? Receiver Relief valve Pressure regulator Dryer Aftercooler Which of the following statements is true? A single acting cylinder may have two ports at two different ends and pressurized fluid can be directed to both of them A single acting cylinder with two ports will can be used as a double acting cylinder A single acting cylinder may have two ports at two different ends but into only one of the ports pressurized fluid is being directed A single acting cylinder…arrow_forwardWhat may be on a coolant reservoir to indicate the coolant level?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY