Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 1, Problem 1.41P
To determine
The rms value of the largest undistorted sinewave output available and input required for the given supplies.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor.
The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for
continuous inductor current. Specify the duty ratio, the switching frequency, the values of
the inductor and capacitor, the peak voltage rating of each device, and the rms current in
the inductor and capacitor. Assume ideal components.
A high voltage engineer cascades 6 stages of a voltage doubler circuit to analyze effectiveness of doing so. Each capacitor
in the circuit is 15 nF, of the input Asupply is 100 kv at Frequency 100 Hz. . so this voltages not
enough with one moudle.So How much moudle
can be in cascades fashion if the load
current is 1 mA.
Q.1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to:
a. 0.625mH and 0.392uF
b. 0.625mH and 0.196uF
c. 0.312mH and 0.196uF
d. None of these
Chapter 1 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 1.1 - Prob. 1.1ECh. 1.1 - Prob. 1.2ECh. 1.1 - Prob. 1.3ECh. 1.1 - Prob. 1.4ECh. 1.2 - Prob. 1.5ECh. 1.2 - Prob. 1.6ECh. 1.2 - Prob. 1.7ECh. 1.2 - Prob. 1.8ECh. 1.3 - Prob. 1.9ECh. 1.4 - Prob. 1.10E
Ch. 1.4 - Prob. 1.11ECh. 1.5 - Prob. 1.12ECh. 1.5 - Prob. 1.13ECh. 1.5 - Prob. 1.14ECh. 1.5 - Prob. 1.15ECh. 1.5 - Prob. 1.16ECh. 1.5 - Prob. 1.17ECh. 1.5 - Prob. 1.18ECh. 1.5 - Prob. 1.19ECh. 1.5 - Prob. 1.20ECh. 1.5 - Prob. 1.21ECh. 1.6 - Prob. 1.22ECh. 1.6 - Prob. D1.23ECh. 1.6 - Prob. D1.24ECh. 1 - Prob. 1.1PCh. 1 - Prob. 1.2PCh. 1 - Prob. 1.3PCh. 1 - Prob. 1.4PCh. 1 - Prob. 1.5PCh. 1 - Prob. 1.6PCh. 1 - Prob. 1.7PCh. 1 - Prob. D1.8PCh. 1 - Prob. D1.9PCh. 1 - Prob. 1.10PCh. 1 - Prob. D1.11PCh. 1 - Prob. D1.12PCh. 1 - Prob. D1.13PCh. 1 - Prob. 1.14PCh. 1 - Prob. 1.15PCh. 1 - Prob. 1.16PCh. 1 - Prob. 1.17PCh. 1 - Prob. 1.18PCh. 1 - Prob. 1.19PCh. 1 - Prob. 1.20PCh. 1 - Prob. 1.21PCh. 1 - Prob. 1.22PCh. 1 - Prob. 1.23PCh. 1 - Prob. 1.24PCh. 1 - Prob. 1.25PCh. 1 - Prob. 1.26PCh. 1 - Prob. 1.27PCh. 1 - Prob. 1.28PCh. 1 - Prob. 1.29PCh. 1 - Prob. 1.30PCh. 1 - Prob. 1.31PCh. 1 - Prob. 1.32PCh. 1 - Prob. 1.33PCh. 1 - Prob. 1.34PCh. 1 - Prob. 1.35PCh. 1 - Prob. 1.36PCh. 1 - Prob. 1.37PCh. 1 - Prob. 1.38PCh. 1 - Prob. 1.39PCh. 1 - Prob. 1.40PCh. 1 - Prob. 1.41PCh. 1 - Prob. 1.42PCh. 1 - Prob. 1.43PCh. 1 - Prob. 1.44PCh. 1 - Prob. 1.45PCh. 1 - Prob. 1.46PCh. 1 - Prob. 1.47PCh. 1 - Prob. 1.48PCh. 1 - Prob. D1.49PCh. 1 - Prob. D1.50PCh. 1 - Prob. D1.51PCh. 1 - Prob. D1.52PCh. 1 - Prob. 1.53PCh. 1 - Prob. 1.54PCh. 1 - Prob. 1.55PCh. 1 - Prob. 1.56PCh. 1 - Prob. D1.57PCh. 1 - Prob. 1.58PCh. 1 - Prob. D1.59PCh. 1 - Prob. D1.60PCh. 1 - Prob. D1.61PCh. 1 - Prob. D1.62PCh. 1 - Prob. 1.63PCh. 1 - Prob. 1.64PCh. 1 - Prob. 1.65PCh. 1 - Prob. 1.66PCh. 1 - Prob. 1.67PCh. 1 - Prob. 1.68PCh. 1 - Prob. 1.69PCh. 1 - Prob. D1.70PCh. 1 - Prob. 1.71PCh. 1 - Prob. 1.72PCh. 1 - Prob. 1.73PCh. 1 - Prob. 1.74PCh. 1 - Prob. D1.75PCh. 1 - Prob. D1.76PCh. 1 - Prob. 1.77PCh. 1 - Prob. 1.78PCh. 1 - Prob. D1.79PCh. 1 - Prob. 1.80PCh. 1 - Prob. 1.81P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E = 0) and the resistance has a value of R = 10 2. The average output voltage is 85% of the maximum possible average output voltage. The delay angle would be equal to: Select one: 81.8° O b. 31.8° O c 67.8° O d. 51.8° AT₁ AT, R L +7=4₂ Warrow_forwarda) Given the choice between a MOSFE Open with for a high voltage application. State your selection with reasons. b) The parameters for the power MOSFET in the circuit shown in the Figure 1 are as follows: rise time, t₁ =2 µs; on resistance, Ros(on) = 0.202; duty cycle, D = 0.7; and switching frequency, f = 30 kHz. Determine: i. the power-loss in the on state. ii. the power-loss during the turn-on interval. Vos 100 V ID D S R₁ = 120 Figure 1 c) Draw a clearly labeled diagram of the thermal equivalent circuit of a transistor. d) The maximum junction temperature of a power transistor is T; = 150 °C and the ambient temperature is T₁ = 25 °C. If the thermal impedances are Rjc = 0.4 C/W, Rcs=0.1 °C/W, and RSA = 0.5 °C/W. Calculate, i. the maximum power dissipation. ii. the case temperature.arrow_forwardGiven the following details: The inverting adder schematic as seen below Vac is an AC voltage source which generates a sine waveform with amplitude 1mV and frequency 1kHz Vout is a sine waveform with amplitude 1V and has a DC offset of 3.5V Find the values of Vdc, R1, R2 and Rf that would satisfy the description for Vout. Assume ideal scenario (i.e. do theoretical computations instead of practical simulations)arrow_forward
- In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.arrow_forwardThe average value of the output voltage with PWM is Vo = 5 V. If the on state duration Ton is 5 µs and supply voltage Vin = 20 V, find the duty ratio d, switching period Ts and switching frequency fs of the system. Draw the waveforms for Vin and Vo voltages stating on and off durations.arrow_forwardConsider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cyclek is first set to 0S. The load is resistive with R-10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch 1V. The RMS output voltage vo is equal to 1124V. The RMS input current and the conduction losses are equal to: Select one: O a.7.95A and 7.95W O b. 11.24A and 11.24w OC. None of these O d. 11.24A and 1263Warrow_forward
- Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage in the range from 10V to 30V. Consider load resistance of 110KQ. Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED?arrow_forward1. The DC-DC converter has several circuit configurations. a) (Draw a simple connection of IGBT switch, diode and inductor that can discriminate between Buck, Boost and Buck-Boost converter circuits respectively.) b) ('A Boost converter produces an output voltage, Vo that is more than or equal to the input voltage, Vi. Based on this statement develop the equation for the relationship between Vo Viand D. where D represents the duty ratio. You can use any suitable diagram to illustrate your answer.)arrow_forward2. A single transistor amplifier is shown in the circuit to the right. The input is a 100 kHz sine wave from a very low impedance source, with a 1 mV peak-to-peak amplitude. hfe, the forward current gain of the transistor, is 300. The base reverse leakage current is 1 nA. The ideality factor for the base-emitter diode is 2, so nkT= 50 mV. a. What are the voltages relative to ground and the currents flowing into, into, and out from the collector, the base, and the emitter, respectively? b. What is the impedance of the 1 µF capacitors at 100 kHz and what effect will this have on the gain of the amplifier? c. What is the gain of the amplifier and how does it depend on the hfe of the transistor? Luff Vin maits Ik { +V₁ = +15V املا Vo Sik Y 1 Fb V₂ I m Vout MF 2K = 250 hfő - -15V --Y₂arrow_forward
- The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15Varrow_forwardWithout changing the locations of the loads in the figure, a) Draw a suitable diagram to measure the active power drawn by the load 22 ONLY using a W-m. b) According to your diagram, express the absolute method error in power measurement by defining the required magnitudes. (Give sufficient explanation). Z1 22 Z3 Z4arrow_forwardConsider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs-160 V. The switching period is 0.25 ms and the duty cycle k is 0.5. The load is resistive with R=10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch 1V. The input power and the conduction losses in the switch are respectively equal to: Select one: a. 1272 W and 7.95W 1264 W and 11.24W 1124 W and 11.24W O b. O c. O d. None of thesearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
What is a Power Amplifier, And Do I Need One?; Author: Sweetwater;https://www.youtube.com/watch?v=2wkmSm4V00M;License: Standard Youtube License