Line AB was determined to be 2395.25m when measured with a 30m‐steel tape supported throughout its length under a pull of 4kg and at a mean temperature of 35°C. The cross‐sectional area of the tape is 0.03 cm^2, coefficient of thermal expansion is 0.0000116/°C and modulus of elasticity of steel is 2.0x10^6 kg/cm^2. Determine a. Correction for the measured length due to temperature if the tape used is of standard length at a temperature of 20°C. Is the tape too long or too short? b. Correction for the measured length due to tension if the tape used is of standard length at a pull of 5 kg. Is the tape too long or too short? c. Correction for the measured length due to sag if it weighs 0.04kg/m d. the corrected length of line AB considering corrections from (a), (b) and (c

Line AB was determined to be 2395.25m when measured with a 30m‐steel tape supported throughout its length under a pull of 4kg and at a mean temperature of 35°C. The cross‐sectional area of the tape is 0.03 cm^2, coefficient of thermal expansion is 0.0000116/°C and modulus of elasticity of steel is 2.0x10^6 kg/cm^2. Determine a. Correction for the measured length due to temperature if the tape used is of standard length at a temperature of 20°C. Is the tape too long or too short? b. Correction for the measured length due to tension if the tape used is of standard length at a pull of 5 kg. Is the tape too long or too short? c. Correction for the measured length due to sag if it weighs 0.04kg/m d. the corrected length of line AB considering corrections from (a), (b) and (c

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum
Q2/Show the mechanical properties changes during tensile test of a metal specimen. Write the mathematical relationships. 443X
X Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.42 in.? and an elastic modulus of 2180 ksi. Bar (2) has a cross-sectional area of 1.139 in.? and an elastic modulus of 4150 ksi. Assume L;-23 in., L2-41 in., Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Determine the horizontal deflection of end Crelative to end A. R (1) (2) P L1 L2 Answer: UCIA - i 0.0725 in.
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
q7 A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be (b) 150 mm3 (d) 130 mm3 (a) 160 mm3 (c) 140 mm3
During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of 0.32in, a tensile load of 40,000 lbs.is applied. If the cross sectional area decreases to 0.3188in and lengthens to 8.021 inches, what is the Modulus of Elasticity and Poisson's Ratio? 29. E= 6/8 v =-ɛ(lateral)/E(axial)
What change in volume would a 100 mm cube of steel suffer at a depth of 5 km in sea water? Take E=2.05 x 10 5N/mm2 and N = 0.82 x 10 5N/mm2
The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured on l. 16 cm gauge length were determined as follows: B A B C Load (kgf) 4800 8400 7200 Elongation (mm) 0.192 28.8 38.4 a) Calculate the proportionality limit, modulus of elasticity, tensile strength, maximum uniform elongation, and contraction-elongation ratio of the metal. b) Since the measured diameter of the metal at break is 12 mm, find the constriction ratio and the actual stress at break.
10:59 0.63 a. Y l KB/S VPN tutorial 1.pdf Axlal 1oads are applied to uie compounu rou inal is composeu of an aluminum segment rigidly connected between steel and bronze segments. (a) What is the stress in each material given that P = 10 kN? (b) Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for 2. Aluminum Steel A=300 mm² Bronze A=400 mm? A=600 mm² 2P 4P 3m -5m 4m bronze. Answer: a) 0one = 50 MPa; ouminum = 33.3 MPa; oel = 100 MPa ; b) P = 12KN A circular aluminum tube of length L = 400 mm is loaded in compression by axial forces P at the ends. The ou inside diameters are 60 mm and 50 mm, respectively. A strain gage is placed on the outside of the bar to measur strains in the longitudinal direction (axial direction). (a) If the measured compressive strain is ɛ = 550×10-6 , what is the shortening ô of the bar? (b) If the compressive stress in the bar is intended to be 40 MPa, what should be the load P? Answer: a) 8 = 0.22…
A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the modulus of elasticity. 120 Upper scale 90 60 Lower scale 30 0.040 0.004 0.060 0.006 0.120 0.012 0.020 0.100 0.010 0.0 0.080 0.008 0.0 0.002 Strain (in./in.) Stress (ksi)
Use modulus of elasticity 30000000 psi
o (ksi) e (in./in.) 33.2 0.0006 45.5 0.0010 49.4 0.0014 51.5 0.0018 53.4 0.0022 Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Determine the modulus of elasticity and the modulus of resilience.