Loose Leaf for Engineering Circuit Analysis Format: Loose-leaf
9th Edition
ISBN: 9781259989452
Author: Hayt
Publisher: Mcgraw Hill Publishers
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 12, Problem 3E
(a)
To determine
The voltage
(b)
To determine
The value of the expression
(c)
To determine
The voltage
(d)
To determine
The voltage
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The voltage between two phases in a balanced three phase-system (4 conductors) is U = 660V.
The voltage between the phase and the neutral is:
a) V = 1143 V
b) V = 660 V
c) V = 381 V
A resistance R-30 2 is connected in series with an inductance (L) of reactance X₁.-40 52 and a capacitor (C)
reactance Xc-40 Q.The equivalent impedance (Z) is equal to:
a) 70 2
b) 30 (2
c) 50 2
The current absorbed by a resistive load of resistance 7.6 0, connected across the terminals of a battery of
electromotive force
E = 14 V and internal resistance r=0.4 0, is:
a) 1 = 1.75 A
b) I= 1.84 A
c) 1 = 35 A
Impedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz ac supply. Z1 =6.25 + j1.25 ohm; Z2 = 5+ j0 ohm and Z3 = 5-jXc ohm. Determine the value of capacitance of Xc such that the total curent of the circuit will be in phase with the total voltage. When is then the circuit current and power.
V:..
H.W. .mp4
www.DANDICAMCO
H.W. 1 Poly-phase Systems
A three phase, four-wire, 208 volt, CBA system has a wyeconnected load with Z, = 60°,
2, = 6/30° and Ze = 5/45°. Obtain the three line currents and the neutral current(in a polar form)
after finding O2 and 03.
A'
120/03
1002
B-
120/150
Chapter 12 Solutions
Loose Leaf for Engineering Circuit Analysis Format: Loose-leaf
Ch. 12.1 - Let and . Find (a) Vad; (b) Vbc; (c) Vcd.Ch. 12.2 - Prob. 2PCh. 12.2 - Modify Fig. 12.9 by adding a 1.5 resistance to...Ch. 12.3 - A balanced three-phase three-wire system has a...Ch. 12.3 - A balanced three-phase three-wire system has a...Ch. 12.3 - Three balanced Y-connected loads are installed on...Ch. 12.4 - Each phase of a balanced three-phase -connected...Ch. 12.4 - Prob. 8PCh. 12.5 - Determine the wattmeter reading in Fig. 12.24,...Ch. 12.5 - Prob. 10P
Ch. 12 - Prob. 1ECh. 12 - Prob. 2ECh. 12 - Prob. 3ECh. 12 - Describe what is meant by a polyphase source,...Ch. 12 - Prob. 5ECh. 12 - Prob. 6ECh. 12 - Prob. 7ECh. 12 - Prob. 8ECh. 12 - Prob. 9ECh. 12 - Prob. 10ECh. 12 - The single-phase three-wire system of Fig. 12.31...Ch. 12 - Prob. 12ECh. 12 - Referring to the balanced load represented in Fig....Ch. 12 - Prob. 14ECh. 12 - Prob. 15ECh. 12 - Consider a simple positive phase sequence,...Ch. 12 - Assume the system shown in Fig. 12.34 is balanced,...Ch. 12 - Repeat Exercise 17 with Rw = 10 , and verify your...Ch. 12 - Prob. 19ECh. 12 - Prob. 20ECh. 12 - Prob. 21ECh. 12 - Prob. 22ECh. 12 - A three-phase system is constructed from a...Ch. 12 - Prob. 24ECh. 12 - Each load in the circuit of Fig. 12.34 is composed...Ch. 12 - Prob. 26ECh. 12 - Prob. 27ECh. 12 - A three-phase load is to be powered by a...Ch. 12 - For the two situations described in Exercise 28,...Ch. 12 - Prob. 30ECh. 12 - Prob. 31ECh. 12 - Prob. 32ECh. 12 - Repeat Exercise 32 if Rw = 1 . Verify your...Ch. 12 - Prob. 34ECh. 12 - Prob. 35ECh. 12 - Prob. 36ECh. 12 - A wattmeter is connected into the circuit of Fig....Ch. 12 - Find the reading of the wattmeter connected in the...Ch. 12 - (a) Find both wattmeter readings in Fig. 12.39 if...Ch. 12 - Circuit values for Fig. 12.40 are , , , , . Find...Ch. 12 - Prob. 41ECh. 12 - Prob. 42ECh. 12 - (a) Is the load represented in Fig. 12.41...Ch. 12 - Prob. 44E
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- c) Drive the expression for maximum phase leads of m given network V. in R₁ min C₁ wwww R2arrow_forwardThree impedances (4-j6) ohm, (6+j8) ohm, and (5-j3) ohms are connected in parallel. Calculate the current in each branch when the total supply current is 20 A. Please provide its solution...its urgently needed...please.arrow_forwardImpedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz acsupply. Z1 =6.25 + j 1.25 ohm; Z2 = 5 + j0 ohm and Z3 = 5 – jXc ohm. Determine the value ofcapacitance of Xc such that the total current of the circuit will be in phase with the totalvoltage. When is then the circuit current and power.arrow_forward
- Using Nodal Analysis, calculate voltages VA, VB and the currents IR1, IR2 and IR6(including direction). do not make source conversions.arrow_forwardChatGPT 3.5 You A balanced load is connected in star across a 3 phase 415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inductance 0.5 henry in parallel with a pure resistance of 28 ohms and a pure capacitor of 60 microfarads capacitance ib each branch Calculate I. The line currents Ii. The overall power factor. iii. The power delivered from the supply. iv. The power dissipated in the resistors and coils. v. The current in the neutral supported by a reason why its value is that deduced ?arrow_forwardEach phase of a balanced three-phase -connected load consists of a 200 mH inductor in series with the parallel combination of a 5 uF capacitor and a 200 ohms resistance. Assume zero line resistance and a phase voltage of 200 V at w = 400 rad/s. a) the magnitude of the phase current is A. Do not write units, round off to three(3) decimal places b) the magnitude of the line current is A. Do not write units, round off to two(2) decimal places c) the total power absorbed by the load is W. Do not write units, No decimal placesarrow_forward
- = = Impedances Z₂ and z3 in parallel are in series with an impedance z₁ across a 100V,50Hz AC supply. Z₁ (6.25 +j1.25)ohms, Z₂ = (5 + j0)ohms and Z3 (5 - jxc)ohms. Determine the value of capacitance Xc said that the total current of the circuit will be in phase with the total voltage. What is then the circuit current and power?arrow_forwardThe impedance Z1 = 6+j8, Z2 = 8 -j6 and Z3 = 10+j0 ohms measured at 50Hz from three branches of a parallel circuit. This circuit is fed from a 100-volt 50-Hz supply. A purely reactive (inductive or capacitive) circuit is added as the fourth parallel branch to the above three-branched parallel circuit so as to draw minimum current from the source. Determine the value of L or C to be used in the fourth branch and also find the minimum current.arrow_forwardThree Impedances each of (8 - j24)2 are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive powerarrow_forward
- Assignment 1 Problem A) Given For the AC circuit in the frequency domain, with a source value Vs = (75 4 45°) V: 3.7502 822 6j Vs + Zeq 1- a b 892 1022 Ix -6j2 16arrow_forward1) Referring to the circuit as in Figure 1, transform the circuit in phasor domain representation.2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.arrow_forwardIn the circuit given in Figure 2, vead(t) = /2-80 cos(4f)V a) Express each circuit element in phasor domain. b) Find the equivalent load impedance (Złoad). c) Calculate the phasor value for the load current Ijoad- Write down time domain expression for the same current ijoad(1). d) Calculate the phasor value for the source voltage Vs. Write down time domain expression for the same voltage v,(t). e) Calculate the active, reactive and apparent power of the load. Determine the power factor. 4H İjoad(t) 5y N v.(t) V load(t) 5H 25mF LOAD allarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Power System Analysis and Design (MindTap Course ...Electrical EngineeringISBN:9781305632134Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. SarmaPublisher:Cengage Learning
Power System Analysis and Design (MindTap Course ...
Electrical Engineering
ISBN:9781305632134
Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma
Publisher:Cengage Learning
How do Electric Transmission Lines Work?; Author: Practical Engineering;https://www.youtube.com/watch?v=qjY31x0m3d8;License: Standard Youtube License